Philips VCB411AT99 - Manual (Page 48)

If you are having problems with your product, check this list of problems and possible solutions before
requesting service. You may be able to solve the problem yourself.
If you need to call a customer service representative, please know the model number and serial number of
your product before you call. This information is displayed on the back of the product. Also, please take a
moment to identify the problem you are having, and be prepared to explain this to the representative. If
you believe the representative will need to help you with operations, please stay near the product. Our
representatives will be happy to assist you.
No power
• Make sure the power plug is completely connected to an AC (alternating current) outlet.
• Make sure the power is turned on.
Power Failure
• Timer recordings and the clock setting may be lost if the power fails for more than one minute. See
pages 15-18 to reset your clock. See pages 33-36 to reprogram your timer recordings. You also may
need to follow the steps on page 11 to set up your language and channels again.
A TV program cannot be recorded.
• Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if
applicable). Details are on pages six-10.
• Make sure the tape has a record tab. Details are on page five.
• Check the TV/VCR position. Details are on page 27.
• Check the CH3/CH4 switch. Details are on pages six-nine.
The VCR will not perform a timer recording.
• Make sure the recording start and stop times are set correctly. Details are on pages 33-36.
• Make sure a tape is in the VCR and the tape has a record tab. Details are on page five. If, after program-
ming a timer recording, you turn off the VCR power without putting a tape in the VCR, the Timer light
will blink.
• If the record tab on a tape is missing, the VCR will eject the tape. The Timer light will blink.
• Make sure the VCR power is off.
• Make sure the clock is set. Details are on pages 15-18.
• The VCR may not perform or continue a timer recording if a power interruption of more than one
minute occurs.
• If you have a Cable Box/Direct Broadcast System, timer recordings are programmed differently. Details
are on page eight.
• Finish programming a timer recording at least five minutes before the recording is set to begin.
• 12 p.m. is noon; 12 a.m. is midnight.
There is no playback picture or the playback picture is noisy or contains streaks.
• Make sure the TV is on the same channel as the VCR’s CH3/CH4 switch.
• Make sure the VCR is in VCR position. (The VCR light will appear on the display panel.)
• Make sure channel 03 or 04 is properly adjusted at the TV.
• Adjust the tracking. Details are on page 42.
• TVs placed too close to the VCR can cause interference during tape playback. Move the VCR away from
the TV.
The VCR cannot be controlled with the remote control.
• Press the VCR button, then try the other VCR feature buttons.
• Make sure the VCR light appears on the display panel. If it does not, press the VCR/TV button once.
• Aim the remote control directly at the VCR’s remote sensor. Details are on page 27.
• Remove all obstacles between the remote control and the VCR.
• Inspect and/or replace the batteries in the remote control. Details are on page five.
The Number buttons won’t work for channels above 69.
• Select CABLE TV at the TUNER SET UP menu (page 12), then let the VCR set up the channels.
• Enter channel numbers as a two-digit number. If you want to select channels 100 and above, enter chan-
nel numbers as a three-digit number. Details are on page 23.
TV programs cannot be watched normally.
• Put the VCR in TV position. (Press the VCR/TV button so that the VCR light disappears from the display
panel.) Details are on page 27.
• Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if
applicable). Details are on pages six-10.
48 Helpful Hints