Philips 60PP9363H-17B - Manual (Page 8)

8
M
ULTIPOINT
R
ED
/B
LUE
T he Multipoint Red/Blue Convergence controls enable you to adjust
the convergence at specific points on the TV screen.
NOTE: The on-screen display will leave the screen after 20 seconds of
inactivity. If this happens, simply press the MENU/SELECT button to
bring the MANUAL CONVERGE submenu back.
1 Press the MENU/SELECT button. The menu appears.
Press the CURSOR RING RIGHT to enter the PICTURE
menu. Then press the CURSOR RING DOWN until MAN-
UAL CONVERGE is highlighted.
2 Press the CURSOR RING RIGHT to enter the MANU-
AL CONVERGE submenu. Press the CURSOR RING
DOWN until MULTIPOINT RED or MULTIPOINT BLUE
is highlighted. Then press the CURSOR RING LEFT or
RIGHT to enter Navigate mode.
3 Press the CURSOR RING LEFT, RIGHT, UP, or
DOWN to move to a cross hair that has a color outline.
Then press the STATUS/EXIT button to enter adjust mode.
4 Press the CURSOR RING LEFT, RIGHT, UP, or
DOWN to adjust the cross hair image until the color
outline is gone. Then press the STATUS/EXIT button to
return to NAVIGATE mode. Repeat steps 3 and 4 until all
misaligned cross images have been adjusted.
5 After making your adjustments, you must store them in
the TV’s memory using SAVE MULTIPOINT.
NOTE: If you are not satisfied with the adjustments you
just made and want to start over, you can use the UNDO
MULTIPOINT control. This control allows you to undo the
adjustments, but it will work only if you use it before sav-
ing.
To save your multipoint adjustments, press the
MENU/SELECT button. This returns you to the MANU-
AL CONVERGE menu. Press the CURSOR RING DOWN
until SAVE MULTIPOINT is highlighted. Then press the
CURSOR RING LEFT or RIGHT to store your adjust-
ments in the TV’s memory.
OR
To undo the multipoint adjustments you just made,
press the MENU/SELECT button. This returns you to
the MANUAL CONVERGE menu. Press the CURSOR
RING DOWN until UNDO MULTIPOINT is highlighted.
Press the CURSOR RING LEFT or RIGHT to undo the
adjustments. Press the CURSOR RING UP until MULTI-
POINT RED or MULTIPOINT BLUE is highlighted. Press
the CURSOR RING LEFT or RIGHT to enter Navigate
mode. Then Follow steps 3–5 above to make your adjust-
ments again.
OR
To restore the TV’s convergence to factory settings,
press the MENU/SELECT button. This returns you to
the MANUAL CONVERGE menu. Press the CURSOR
RING DOWN until RESTORE FACTORY is highlighted.
Then press the CURSOR RING LEFT or RIGHT to restore
the TV’s convergence to factory settings.
6 Press the STATUS/EXIT button to exit the submenu.
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
PICTURE
MANUAL CONVERGE
É
▲▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
PICTURE
MANUAL CONVERGE
PIP
2 1 3
5 4 6
8 7 9
0
TV
SWAP PIP CH
DN UP
FREEZE
SOUND
MUTE
SURF A/CH
POWER
PICTURE
STATUS/
EXIT
POSITION
VCR ACC
MENU/
SELECT
VOL CH
TV/VCR
ACTIVE
CONTROL
1,5
3,4
to Navigate Exit to Adjust
to Navigate Exit to Adjust
to Adjust Exit to Navigate
PI
▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
PICTURE
MANUAL CONVERGE
SAVE MULTIPOIN
PI
OR
▲
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT
PICTURE
MANUAL CONVERGE
UNDO MULTIPOI
PI
OR
RESTORE FACTO
PI
▲
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT
RESTORE FACTORY
PICTURE
MANUAL CONVERGE
6
2
H ELPFUL H INT
If you should experi-
ence a power outage
before saving your mul-
tipoint-convergence set-
tings, your settings will