Philips AZ3300-37 - Manual (Page 8)

• Dès que l’achat de votre appareil
Philips est enregistré, vous avez droit à
tous les avantages dont bénéficient les
possesseurs des produits Philips.
• Remplissez et renvoyez votre carte
d’enregistrement de garantie jointe à
votre appareil sans tarder et vous béné-
ficierez de ces avantages importants.
Renvoyez votre carte d’enregistrement de garantie pour vous
assurer de recevoir tous les avantages auxquels vous avez droit.
Vérification
de garantie
Enregistrez votre produit
dans les 10 jours pour
confirmer votre droit à
une protection maximum
selon les termes et les
conditions de votre
garantie Philips.
Confirmation
de possession
Votre carte d’enreg-
istrement de garantie
prouve que vous possédez
l’appareil en cas de vol ou
de perte du produit.
Enregistrement
du modèle
Renvoyez votre carte d’en-
registrement de garantie dès
aujourd’hui pour vous assur-
er de recevoir toutes les
informations, les offres et les
bonus auxquels vous avez
droit en tant que possesseur
de ce modèle.
Cet « éclair à pointe de
flèche » indique qu’un matéri-
au non isolé, situé à l’intérieur
de l’unité, risque de provoquer un choc
électrique. Pour la sécurité de chacun,
nous vous prions de ne pas retirer le
boîtier de ce produit.
Le « point d’exclamation »
attire votre attention sur des
sujets risquant de provoquer
des problèmes de fonctionnement et
d’entretien si vous ne lisez pas les infor-
mations s’y reportant.
DANGER:
ATTENTION: Pour éviter les
chocs électriques, introduire la lame la
plus large de la fiche dans la borne
correspondante de la prise et pousser
jusqu’au f
ond.
Cet espace vous est réservé
Inscrivez ci-dessous le numéro de série situé
à l’arrière du bloc. Conservez cette informa-
tion pour vous y reporter à l’avenir.
N ° de modèle ____________________
N ° de série ______________________
MAC5097
Connaissez ces
symboles de
sécurite
A T T E N T I O N
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ATTENTION: POUR REDUIRE LE RESQUE DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE (NI LE PANNEAU ARRIERE). CET APPAREIL NE COMPORTE AUCUNE PIECE POUVANT TRE REPAREE PAR L’UTILISATEUR. CONFIER SON ENTRETIEN A UN TECHNICIEN QUALIFIE.
DE FEU OU DE CHOC ÉLECTRIQUE, CET
APPAREIL NE DOIT PAS ETRE EXPOSÉ À LA
PLUIE OU À L'HUMIDITÉ ; D'AUTRE PART,
AUCUN OBJET CONTENANT DU LIQUIDE,
TEL QU'UN VASE, NE DOIT ETRE DISPOSÉ
SUR CET APPAREIL.
AFIN D'ÉVITER TOUT RISQUE
• Una vez que se registre la compra de
su aparato Philips, Ud. tiene derecho a
todas las ventajas correspondientes al
dueño de un producto Philips.
• Sírvase llenar y devolver en seguida
la Tarjeta de Registro de la Garantía
empacada con su aparato y saque
provecho de estas ventajas importantes.
Envie hoy su Tarjeta de Registro de la Garantía
para recibir todas las ventajas correspondientes.
Verificación
de la garantía
Registre su producto den-
tro de 10 días para confir-
mar su derecho a máxima
protección bajo los térmi-
nos y condiciones de la
garantía de Philips.
Confirmación
del dueño
Su Tarjeta de Registro de
la Garantía comprueba
que Ud. es el dueño del
aparato en caso de robo
o pérdida del producto.
Registro
del modelo
La devolución inmediata de
su Tarjeta de Registro de la
Garantía le garantiza que
recibirá toda la información
y todas las promociones
especiales que le corre-
sponden por ser el dueño
de su modelo.
El símbolo del «rayo» indica
que algún material no aislado
dentro de su unidad podría
resultar en una sacudida eléctrica. Para
la seguridad de todos, favor de no
remover la cubierta del producto.
El «signo de exclamación» le
llama la atención a carac-
terísticas sobre las que Ud.
debe leer la información adjunta
detenidamente para evitar problemas
de funcionamiento y mantenimiento.
ADVERTENCIA:
PRECAUCION: Para evitar
sacudida eléctrica, introduzca la patilla
ancha del enchufe al f
ondo de la ranu-
ra ancha.
Para uso del cliente:
Escriba abajo el número de serie que se
encuentra en el panel posterior. Guarde
esta información para el futuro.
No. de modelo ____________________
No. de serie ______________________
MAC5097
Conozca estos
simbolos de
seguridad
PRECAUCION
RIESGO DE SACUDIDA ELECTRICA NO ABRIR
PRECAUCION: PARA REDUCIR EL RIESGO DE SACUDIDA ELECTRICA,NO RETIRE LA CUBIERTA (NI EL PANEL POSTERIOR). ESTE APARATONO CONTIENE NINGUNA PARTE QUE PUEDA SER REPARADA POREL USARIO. DE SER NECESARIO ALGUN SERVICIO O REPARACIONDEL APARATO, LLEVELO UN TECNICO CALIFICADO.
PARA REDUCIR
EL RIESGO DE INCENDIO O DESCARGA
ELÉCTRICA, ESTE APARATO NO DEBE
EXPONERSE A LA LLUVIA NI LA HUMEDAD,
Y NO SE DEBE COLOCAR SOBRE EL
APARATO NINGÚN OBJETO QUE
CONTENGA LÍQUIDO, POR EJEMPLO UNA
JARRA.
• Once your Philips purchase is registered,
you’re eligible to receive all the privileges
of owning a Philips product.
• So complete and return the Warranty
Registration Card enclosed with your
purchase at once, and take advantage
of these important benefits.
Return your Warranty Registration card today to
ensure you receive all the benefits you’re entitled to.
Warranty
Verification
Registering your product
within 10 days confirms
your right to maximum
protection under the
terms and conditions of
your Philips warranty.
Owner
Confirmation
Your completed Warranty
Registration Card serves
as verification of owner-
ship in the event of prod-
uct theft or loss.
Model
Registration
Returning your Warranty
Registration Card right
away guarantees you’ll
receive all the information
and special offers which
you qualify for as the
owner of your model.
This “bolt of lightning” indi-
cates uninsulated material
within your unit may cause
an electrical shock. For the safety of
everyone in your household, please do
not remove product covering.
The “exclamation point” calls
attention to features for
which you should read the
enclosed literature closely to prevent
operating and maintenance problems.
WARNING:
CAUTION: To prevent electric
shock, match wide blade of plug to
wide slot, and fully insert.
For Customer Use
Enter below the Serial No. which is locat-
ed on the rear of the cabinet. Retain this
information for future reference.
Model No. _______________________
Serial No. ________________________
MAC5097
Know these
safety
symbols
C A U T I O N
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, THIS APPARATUS
SHOULD NOT BE EXPOSED TO RAIN OR
MOISTURE, AND OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHOULD NOT
BE PLACED ON THIS APPARATUS.
Class II equipment symbol
This symbol indicates that the unit has a double insulation system.
Símbolo del equipo Clase II
Este símbolo indica que la unidad tiene un sistema doble de aislamiento.
Symbole d’ un appareil de classe II
Ce symbole indique que l’appareil est équipé d’un système à double isolation.
1. Lea estas instrucciones.
2. Conserve estas instrucciones.
3. Lea todos los avisos.
4. Siga todas las instrucciones.
5. No utilice este aparato cerca del
agua.
6. Para limpiar el aparato utilice sólo
un trapo seco.
7. No tape las aperturas de venti-
lación. Proceda a su instalación de
acuerdo con las instrucciones del
fabricante.
8. No instale el equipo cerca de fuentes
de calor – Como radiadores, calentadores,
estufas o cualquier otro aparato (incluyen-
do los amplificadores) generador de calor.
9. No anule la
seguridad de la
clavija de corriente
(ya sea de tipo polar-
izado o
con toma de tierra). Las clavijas polarizadas
tienen dos patillas, una más ancha que la
otra. Las que disponen de toma de tierra
tienen dos patillas y una tercera que es la
de conexión a tierra.Tanto la patilla más
ancha como la toma de tierra han sido
incorporadas a la clavija para su seguridad
personal. Si la clavija suministrada con el
equipo no es compatible con su toma de
corriente, consulte a un electricista para
sustituir la toma de corriente obsoleta.
10. Proteja debidamente el cable impi-
diendo que pueda pisarse o incluso per-
forarse, especialmente en la parte más
próxima a la clavija y en el punto de salida
del equipo.
11. Utilice exclusivamente aquellos dis-
positivos/ accesorios recomendados
por el fabricante.
12. Coloque el equipo exclusi-
vamente sobre aquellos carros,
bases, trípodes, soportes o
mesas especificados por el com-
erciante o vendidos con el
equipo. Cuando utilice un carro,
tenga cuidado al desplazar el
conjunto carro/ equipo para evi-
tar posibles daños por vuelco.
13. Desenchufe el aparato durante tor-
mentas eléctricas o cuando no vaya a ser
utilizado durante largo tiempo.
14. Confíe el mantenimiento y las
reparaciones a personal técnico especial-
izado. El equipo deberá repararse siempre
que haya resultado dañado de alguna man-
era, como por ejemplo por daños en el
cable o en la clavija, por derrame de líqui-
do sobre el equipo, por objetos que
hubieran podido introducirse en su interior,
por exposición del equipo a la lluvia o a
ambientes húmedos, cuando el equipo no
funcione con normalidad o cuando hubiera
sufrido algún tipo de caída.
15. Uso de las pilas – ADVERTENCIA: Para
prevenir escapes en las pilas, que pueden
ocasionar lesiones físicas, daños a
su propiedad o dañar la unidad:
● Instale todas las pilas correctamente, + y -
como está marcado en la unidad.
● No mezcle las pilas (viejas con nuevas o
de carbono y alcalinas, etc.).
● Extraiga las pilas cuando no vaya a usar la
unidad durante largo tiempo.
EL 6475-S003: 02/8
Programming track numbers
In the stop position, select and store your CD tracks in
the desired sequence. Up to 20 tracks can be stored in
the memory.
1. Press SEARCH ∞ or § on the set to select your
desired track number.
2. Press PROGRAM.
™ Display: PROGRAM, Prog briefly and your
selected track number. (See 5)
™ If you attempt to program without first
selecting a track number, noSE is shown.
3. Repeat steps 1-2 to select and store all desired
tracks.
™ Display: FULL if you try to program more
than 20 tracks.
Reviewing the program
In the stop position, press and hold PROGRAM until
the display shows all your stored track numbers in
sequence.
Erasing a program
You can erase the program by either:
• pressing 9 twice
™ CLr is displayed briefly and PROGRAM
disappears.
• You select FM / AM function.
• Open the CD door.
SAFETY & MAINTENANCE INFORMATION
(See 7)
• Don't expose the set, batteries, CDs to humidity,
rain, sand or excessive heat.
• Clean the set with a dry cloth. Don't use any
cleaning agents containing alcohol, ammonia,
benzene or abrasives as these may harm the set.
• Place the set on a hard and flat surface so that the
system does not tilt. Make sure there is good
ventilation to prevent the set overheating.
• The mechanical parts of the set contain
self-lubricating bearings and must not be oiled or
lubricated.
CD player and CD handling
• If the CD player cannot read CDs correctly, use a
cleaning CD to clean the lens before taking the set
to repair.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature
can cause condensation on the lens of your CD
player. Playing a CD is then not possible. Do not
attempt to clean the lens but leave the set in a
warm environment until the moisture evaporates.
• Always close the CD door to avoid dust on the lens.
• To clean the CD, wipe in a straight line from the
center towards the edge using a soft, lint-free
cloth. Do not use cleaning agents as they may
damage the disc.
• Never write on a CD or attach any stickers to it.
No sound /power
– Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries drained/ incorrectly inserted
• Insert (fresh) batteries correctly
Severe radio hum or noise
– Electrical interference: set too close to TV, VCR or
computer
• Move the set to increase the distance
Poor radio reception
– Weak radio signal
• FM: Adjust the FM telescopic antenna
nocd indication
– CD badly scratched or dirty
• Replace/ clean CD, see Maintenance
– Laser lens steamed up
• Wait until lens has cleared
nFcd indication
– CD-R(W) is blank/ not finalized
• Use a finalized CD-R(W)
dAtA indication
– CD contains non-audio files
• Press SEARCH
∞ or § once or more to skip to a
CD audio track, instead of the data file
The CD skips tracks
– CD damaged or dirty
• Replace or clean CD
– SHUFFLE or PROGRAM is active
• Switch off SHUFFLE / PROGRAM
Remote control does not function properly
– Batteries exhausted/ incorrectly inserted
• Insert (fresh) batteries correctly
– Distance/ angle between the set too large
• Reduce the distance/ angle
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near
water.
6. Clean only with dry cloth.
7. Do not block any ventilation open-
ings. Install in accordance with the
manufacturer´s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
9. Do not defeat
the safety
purpose of the
polarized or
grounding-type plug. A polarized plug has
two blades with one wider than the other.
A grounding type plug has two blades and
a third grounding prong.The wide blade or
the third prong are provided for your safe-
ty. If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart,
stand, tripod, bracket, or table
specified by the manufacturer or
sold with the apparatus. When a
cart is used, use caution when
moving the cart/apparatus com-
bination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is dam-
aged, liquid has been spilled or objects
have fallen into the apparatus, the appara-
tus has been exposed to rain or moisture,
does not operate normally, or has been
dropped.
15. Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
● Install all batteries correctly, + and - as
marked on the unit.
● Do not mix batteries (old and new or
carbon and alkaline, etc.).
● Remove batteries when the unit is not
used for a long time.
EL 6475-E004: 02/8
ACCESSORIES
1 x AC power cord
1 x Remote Control
TOP AND FRONT PANEL (See 1)
1 PROGRAM
CD: - programs tracks and reviews the program;
Tuner: - programs preset radio stations.
2 CD•FM•AM - selects CD /FM / AM function
3 IR SENSOR - infrared for remote control
4 TUNER PRESET 4 ,3 - selects a preset radio
station.
5 OPEN•CLOSE - opens / closes CD door.
6 Telescopic antenna - improves FM reception.
7 VOLUME + , - - to adjust volume level.
8 DBB (Dynamic Bass Boost) - activates a more vivid
bass response.
9 2; - starts or pauses CD playback.
9 - to stop playback or erase a CD program.
SEARCH
∞ , §
CD: - searches backward and forward within a track;
- skips to the beginning of a current track/
previous/ later track.
Tuner: - (down, up) tunes to radio stations.
0 POWER - power on / off switch
! MODE - selects different play modes: e.g. REPEAT
or SHUFFLE (random) order.
@ Display - shows the status of the set.
BACK PANEL (See 1)
# AC MAINS - inlet for power cord.
$ Battery compartment - for 6 batteries, type
R-14, UM2 or C-cells.
REMOTE CONTROL (See A)
1 CD – selects CD sound source
2 y – switches the set to standby / on if set
operating on AC power. (Switches set off only if
battery powered)
3 VOLUME + , - – adjusts volume level (up, down)
4SHUFFLE – plays all CD tracks in random order
5BASS – selects DBB on/off
6
2; – starts/ pauses CD playback
7SEARCH 5, 6 – searches backwards/ forwards
within a track
8BAND – selects FM (AM) waveband
9PRESET
3, 4 – selects a preset radio station
(up, down)
0TUNING ∞, § – tunes to tuner stations
(down, up)
!TUNER – selects tuner sound source
@
9 – stops CD playback;
– erases a CD programme
# ¡, ™ – skips to the beginning of a current track
previous/ subsequent track
$MUTE – interrupts/ resumes sound
%REPEAT – repeats a track /programme/ entire CD
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous radiation
exposure or other unsafe operation.
POWER SUPPLY
Whenever convenient, use the AC power supply to
conserve battery life. Make sure you remove the
power plug from the set and wall outlet before
inserting batteries.
Batteries (not included)
• Insert 6 batteries, type R-14, UM-2 or C-cells,
(preferably alkaline) with the correct polarity. (See 6)
• Remote control
Insert 2 batteries, type AAA, R03 or UM4
(preferably alkaline). (See 8)
IMPORTANT!
• Incorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or cause
the batteries to burst.
• Do not mix battery types: e.g. alkaline with carbon
zinc. Only use batteries of the same type for the
set.
• When inserting new batteries, do not try to mix old
batteries with the new ones.
• Batteries contain chemical substances, so
they should be disposed of properly.
Using AC Power
1. Check if the AC power supply, as shown on the
type plate located on the bottom of the set,
corresponds to your local power supply. If it does
not, consult your dealer or service center.
2. Connect the power cord to the outlet.
3. To disconnect the power supply, unplug the set
from the outlet.
Storing your remote control
This set has a special built-in storage compartment for
your remote control. The storage compartment has a
latch to keep your remote control in place, and is
located inside the CD compartment. (See B)
Placing your set
To avoid possible staining
of surfaces, please do not
stand this set in vertical
position over a long
period.
The type plate is located on the bottom of the
set.
BASIC FUNCTIONS
Switching on and off and selecting function
1. Press POWER on the set (or y on remote
control) to switch on.
2. Press CD•FM•AM once or more to select :
CD / Tuner function, and operate the respective
function controls.
3. Press POWER to switch off the set.
Note : The DBB setting, radio band preset and the
volume level (maximum to 20) will be retained in the
set's memory.
Adjusting volume and sound (See 2)
1. Adjust the volume with the VOLUME
+ , - controls.
™ Display shows the volume level in number from
0-32.
2. Press DBB once or more to select dynamic bass
boost on or off.
™ Display: shows when activated.
IMPORTANT SAFETY INSTRUCTIONS English CONTROL
1. Lisez ces instructions.
2. Conservez ces instructions.
3. Respectez les avertissements.
4. Suivez toutes les instructions.
5. N’utilisez pas cet appareil à proximité d’une
source d’eau.
6. Nettoyez l’appareil uniquement avec un chif-
fon sec.
7. N’obstruez aucun orifice de ventilation.
Installez l’appareil selon les instructions du
fabricant.
8. N’installez pas l’appareil près d’une source de
chaleur comme par exemple des radiateurs, bouches
de chaleur, cuisinières, ou autres appareils (même des
amplificateurs) dégageant de la chaleur.
9. Ne détruisez pas la sécurité incorporée dans la
prise de terre ou prise
polarisée fournie. Une
prise polarisée est dotée de
deux lames
dont une plus large que l’autre. Une prise de terre est
dotée de deux fiches semblables et d’une troisième,
plus large, qui assure la mise à la terre pour votre
sécurité. Si la prise fournie ne convient pas à la prise
murale dont vous disposez, consultez un électricien
pour remplacer et adapter votre prise murale.
10. Protégez le cordon d’alimentation pour éviter
de marcher dessus ou de le pincer particulièrement
aux endroits des prises, mâles et femelles, et au point
de raccordement sur l’appareil lui-même.
11. Utilisez uniquement des accessoires ou
options recommandés par le fabricant.
12. Utilisez uniquement un meuble
sur roulettes, un support, un pied, une
étagère ou une table de type recom-
mandé par le fabricant. Si vous utilisez un
meuble sur roulettes, veillez à le déplacer
avec précaution afin d’éviter tout acci-
dent corporel si l’équipement se renver-
sait.
13. Débranchez l’appareil pendant les orages ou s’il
doit rester inutilisé pendant une période de temps
prolongée.
14. Pour toute réparation, faites appel à un personnel
qualifié. Une réparation sera nécessaire si l’appareil a
subi des dommages tels que détérioration du cordon
d’alimentation ou de la prise, liquide renversé sur l’ap-
pareil, ou encore si un objet est tombé dessus, si l’ap-
pareil a été exposé à la pluie ou à l’humidité, s’il ne
fonctionne pas correctement ou s’il a fait une chute.
15. PRÉCAUTION d’emploi des piles – Afin d’éviter
toute fuite des piles qui risquerait de causer des
blessures corporelles, des dommages matériels, ou
d’endommager l’appareil :
● Installez toutes les piles correctement, + et - tels
qu’indiqués sur l’appareil.
● Ne mélangez pas les piles (pas de piles neuves avec
des usagées ou de piles au carbone avec des alca-
lines, etc.).
● Enlevez les piles lorsque l’appareil reste inutilisé pen-
dant une longue période.
EL 6475-F003: 02/8
DIGITAL TUNER
Tuning to radio stations
1. Press POWER to on, then press CD•FM•AM (or
TUNER on remote control) to select TUNER.
™ TU is displayed briefly and then the radio
station frequency, waveband and, if
programmed, a preset number are shown (See 3)
2. Press CD•FM•AM ( or BAND on remote control)
once or more to select your waveband.
3. Press and hold SEARCH ∞ or § until the
frequency in the display starts running.
™ The radio automatically tunes to a station of
sufficient reception. Display shows Srch
during automatic tuning.
4. Repeat step 2 if necessary until you find the
desired station.
• To tune to a weak station, press ∞ or § briefly
and repeatedly until you have found optimal
reception.
To improve radio reception:
• For FM, extend, incline and turn the telescopic
antenna. Reduce its length if the signal is too
strong.
• For AM , the set uses a built-in antenna. Direct this
antenna by turning the whole set.
Programming radio stations
You can store up to a total of 30 radio stations (20 FM
and 10 AM) in the memory, manually or automatically
(Autostore).
Manual programming
1. Tune to your desired station (see Tuning to radio
stations).
2. Press PROGRAM to activate programming.
™ PROGRAM flashes.
3. Press TUNER PRESET 4 ,3 once or more to select
a preset number.
• Remote control : Press PRESET 3, 4 once or
more to select a preset station.
4. Press PROGRAM to confirm.
5. Repeat steps 1-4 to store other stations.
Note : You can erase a preset station by storing
another frequency in its place.
Autostore
Autostore automatically starts programming radio
stations from preset 1. Available stations are
programmed in order if the station with sufficient
reception strength. Any previous presets e.g. manually
programmed will be erased.
• Press PROGRAM for 2 seconds or more to acti-
vate autostore programming.
™ The display shows AUtO, PROGRAM blinks,
followed by the radio station details when
stored.
After all stations are stored, the first preset station
will then automatically play.
To listen to a preset station
• Press the TUNER PRESET 4 ,3 buttons once or
more until the desired preset station is displayed.
• Remote control : optionally, press PRESET 3, 4 to
select your preset station.
Playing a CD
This CD player plays Audio Discs including CD-
Recordables and CD-Rewritables.
1. Adjust the CD•FM•AM to CD.
2. Open the CD Door.
™ OPEN is displayed.
3. Insert a CD with the printed side facing up and
close the door.
™ nocd if no CD inserted/ CD dirty, incorrectly
inserted or damaged.
™ nFcd if you have inserted a non-finalized CD-
R(W).
4. Press 2; to start playback.
™ dAtA if your CD contains non-audio i.e. data
files.
5. To pause playback press 2;. Press 2; again to
resume play.
™ Display: B flashes during pause.
6. To stop CD playback, press the 9 button.
Note : CD play will also stop when:
- the CD door is opened
- the CD has reached the end
- you select FM / AM function.
Selecting a different track
• Press SEARCH ∞ or § once or repeatedly to
select your track.
• In the pause / stop position, press 2; to start
playback.
Finding a passage within a track
1. Press and hold SEARCH ∞ or §.
– The CD is played at high speed and low volume.
2. When you recognize the passage you want,
release ∞ or § to resume normal playback.
Note : During a CD program or if SHUFFLE/
REPEAT active, searching is only possible within a
track.
Different play modes: SHUFFLE and REPEAT
You can select and change the various play modes
before or during playback, and combine the modes
with PROGRAM. (See 4)
SHUFFLE - tracks of the entire CD/ program
are played in random order
SHUFFLE REPEAT ALL - to repeat the
entire CD/ program continuously in random order
REPEAT ALL - repeats the entire CD/ program
REPEAT - plays the current track continuously
1. To select play mode, press MODE once or more.
2. Press 2; to start playback if in the stop position.
3. To select normal playback, press MODE
repeatedly until the various modes are no longer
displayed.
– You can also press the 9 button to cancel your
play mode.
CONSIGNES DE SÉCURITÉ IMPORTANTES DIGITAL TUNER DIGITAL TUNER CD PLAYER CD PLAYER
INSTRUCCIONES IMPORTANTES DE SEGURIDAD CD PLAYER SAFETY AND MAINTENANCE TROUBLESHOOTING
POWER SUPPLY BASIC FUNCTIONS
PHILIPS CONSUMER ELECTRONICS NORTH AMERICA
Knoxville, Tennessee 37914-1810, U.S.A.
AZ 3300 AZ
3300 CD Soundmachine
Need help? Call us!
Philips representatives are ready to help you with
any questions about your new product. We can guide you
through Connections, First-time Setup, or any of the Features.
We want you to start enjoying your new product right away!
CALL US BEFORE YOU CONSIDER
RETURNING THE PRODUCT!
1-800-531-0039
or
Visit us on the web at www.philips.com
S EE W HY INS ID E
IM
PO RTAN
T ! Return
your Warranty Registration Card
within 10 days
Printed in China
W
CLASS 1
LASER PRODUCT
AZ 3300
English
F ran
ç ais
Espa
ñ ol
Environmental information
We have done our best to reduce the packaging and make it easy to separate into 3 materials:
cardboard, expandable polystyrene, polyethylene.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packaging, dead batteries and old equipment.
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service center.
WARNING: Do not open the set as there is a risk of electric shock. Under no cir-
cumstances should you try to repair the set yourself, as this will
invalidate the warranty.
AC Polarized
Plug
Prise
polarisée C.A.
English:This digital apparatus does not exceed the Class B limits for radio noise emis-
sions from digital apparatus as set out in the Radio Interference Regulations of the Cana-
dian Department of Communications.
Français: Cet appareil numérique n'émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de Classe B prescrites dans le Règlement sur
le Brouillage Radioélectrique édicté par le Ministère des Communications du Canada.
Canada
Clavija polarizada de CA
The set complies with the FCC-Rules, Part 15 and with 21 CFR 1040.10.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
L’appareil répond aux normes FCC, Part 15 et 21 CFR 1040.10.
Fonctionnement soumis aux deux conditions suivantes :
1. Cet appareil ne doit pas provoquer d’interférences nuisibles, et
2. Cet appareil doit accepter toute interférence reçue, y compris les interférences
susceptibles de provoquer un fonctionement peu satisfaisant.
El aparato cumple las normas FCC, Parte 15 y 21 CFR 1040.10.
Funcionamiento dependiente de dos condiciones siguientes:
1. Este aparato no puede provocar interferencia dañina, y
2. Este aparato debe aceptar cualquier interferencia recibida, incluyendo las
interferencias que pueden provocar un funcionamiento insuficiente.
Meet Philips at the Internet
http://www.philips.com
PORTABLE AUDIO
One Year Free Exchange
This product must be carried in for an exchange.
LIMITED WARRANTY
WHO IS COVERED?
You must have proof of purchase to exchange the product.
A sales receipt or other document showing that you pur-
chased the product is considered proof of purchase. Attach
it to this owner’s manual and keep both nearby.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product.
For one year thereafter, a defective or inoperative product
will be replaced with a new, renewed or comparable prod-
uct at no charge to you. A replacement product is covered
only for the original warranty period.When the warranty
on the original product expires, the warranty on the
replacement product also expires.
WHAT IS EXCLUDED?
Your warranty does not cover:
•
labor charges for installation or setup of the product,
adjustment of customer controls on the product, and
installation or repair of antenna systems outside of the
product.
• product repair and/or part replacement because of
misuse, accident, unauthorized repair or other cause
not within the control of Philips.
• reception problems caused by signal conditions or
cable or antenna systems outside the unit.
• a product that requires modification or adaptation to
enable it to operate in any country other than the
country for which it was designed, manufactured,
approved and/or authorized, or repair of products
damaged by these modifications.
• incidental or consequential damages resulting from the
product. (Some states do not allow the exclusion of
incidental or consequential damages, so the above
exclusion may not apply to you.This includes, but is not
limited to, prerecorded material, whether copyrighted
or not copyrighted.)
• a product used for commercial or institutional purposes.
WHERE IS EXCHANGE AVAILABLE?
You may exchange the product in all countries where the
product is officially distributed by Philips. In countries
where Philips does not distribute the product, the local
Philips service organization will attempt to provide a
replacement product (although there may be a delay if the
appropriate product is not readily available).
BEFORE REQUESTING EXCHANGE...
Please check your owner's manual for assistance. If you
have additional questions, call us at 1-800-531-0039.
EXCHANGING A PRODUCT IN U.S.A.,
PUERTO RICO, OR U.S.VIRGIN ISLANDS...
Contact 1-800-531-0039 to arrange an exchange. Or, ship
the product, insured and freight prepaid, and with proof of
purchase enclosed, to the address listed below.
Philips Exchange Program Suite A
406 North Irish Street
Greeneville TN 37745
(In U.S.A., Puerto Rico, and U.S.Virgin Islands, all implied war-
ranties, including implied warranties of merchantability and fit-
ness for a particular purpose, are limited in duration to the
duration of this express warranty. But, because some states do
not allow limitations on how long an implied warranty may
last, this limitation may not apply to you.)
EXCHANGING A PRODUCT IN CANADA...
Please contact Philips at:
1-800-661-6162 (French Speaking)
1-800-531-0039 (English or Spanish Speaking)
(In Canada, this warranty is given in lieu of all other war-
ranties. No other warranties are expressed or implied,
including any implied warranties of merchantability or fit-
ness for a particular purpose. Philips is not liable under any
circumstances for any direct, indirect, special, incidental or
consequential damages, howsoever incurred, even if notified
of the possibility of such damages.)
REMEMBER...
Please record below the model and serial numbers found
on the product. Also, please fill out and mail your warranty
registration card promptly. It will be easier for us to notify
you if necessary.
MODEL # __________________________________
SERIAL # __________________________________
EL6095T004 / 8-02
This warranty gives you specific legal rights.You may have other rights which vary from state/province to state/province.
Philips, P.O. Box 520890, Miami, FL 33152, USA, (402) 536-4171
X
2
FM
3
DBB
4
PROGRAM
5
8
7
6
See A
2
3 B CD
VOLUME
SEARCH
PRESET
TUNING DIGITAL REMOT E CONT ROL
BAND TUNER
REPEAT
MUTE BASS
SHUFFLE
3
4 0
4
5
7
6
8
9
1
%
$
#
!
@
1
2
3
4
5
7
8
!
9
$
#
0
DBB
PR O G R A M
M O D E
POWER
V O LU M E
STO P SEARCH
PL AY •PA US E
TUNER PR ESET
OP EN •CLO SE
AZ3 300 CD SOUNDMA CHINE
CD•FM•AM IR SENSOR
See B
B CD
RE PEA T
3 4
SE AR CH
PR ES ET
TU NI NG
DIGIT AL REM OTE CON TROL
BA ND
TU NE R
@
VO LU ME SHUFFLE
6
1
AZ3300/17 4/2/03 5:48 PM Page 1