Philips AZ1835-37 - Manual (Page 5)

Supplied accessories
– AC power cord
– Remote control
Top and front panels (See 1)
1 Source selector: CD/USB,TUNER, OFF
– selects CD/MP3-CD (or USB mode), or
radio
– switches off the set
2 VOLUME – adjusts volume level
3 LIFT TO OPEN – lifts here to open the
disc door
4 +/-
– For MP3-CD/ WMA/USB play: select
albums
5 9 – stops disc/USB playback;
– erases a program
6 iR – infrared sensor for remote control
7 Display – shows disc/USB play functions
8 DBB – turns the bass enhancement on/off.
9 PROG – programs tracks and reviews the
program
0 USB REC – copy one file or all files of a disc
to an external portable USB
storage device/MP3 player
! MODE – selects different play modes:
e.g. REPEAT or SHUFFLE (random order)
@ USB port – connects an external USB mass
storage device
# CD/USB – enters disc or USB mode
$ BAND – selects wavebands, AM or FM
% Frequency indicator – shows the radio fre-
quency of your selected waveband
^ TUNING – tunes to radio stations
& ∞ §
– For disc/ USB play:
– skips to the beginning of a current/
previous/ later track
– fast searches backwards and forwards
within a track
* 2; – starts or pauses disc/USB playback
Back panel (See 1)
( Telescopic antenna – improves FM
reception
) Battery door – open to insert 6 x 1.5V
R-14/ UM2/ C-cells
¡ AC~ MAINS – inlet for power cord
Remote control (See 1)
1 CD – enters disc mode
2 USB – enters disc or USB mode
3 MODE – selects different play modes: e.g.
REPEAT or SHUFFLE
(random order)
4 PROG – programs tracks and reviews the
program
5 9 – stops disc/USB playback;
– erases a program
6 2; – starts/ pauses CD/USB playback
7 ∞ §
For disc/ USB play:
– fast searches back and forward
– skips to the beginning of a current track/
previous/ later track
8 ALBUM +/-
For MP3-CD/USB play: selects albums
9 DEL – deletes one file or all files stored on
the external USB device
0 REC – copy one file or all files of a disc to the
external USB device
Power Supply
Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries
Main set (See 1)
• Insert 6 batteries, type R-14, UM2 or C-
cells (not included, preferably alkaline) with
the correct polarity.
Remote control
Important!
•
Before using the remote control, remove
the insulation plastic tab as shown
in figure @.
• If the remote control does not function
correctly or the operating range is
reduced, replace the battery with a new
(CR2025) type battery
1 Press and hold the latch (A) in the direction
as shown in figure @.
2 Simultaneously, pull the battery tray (B) out.
3 Replace a new battery, and fully insert the
battery tray back to the original position.
• Incorrect use of batteries can cause elec-
trolyte leakage and will corrode the compart-
ment or cause the batteries to burst:
• Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same
type for the set.
• When inserting new batteries, do not try to
mix old batteries with the new ones.
• Remove the batteries if the set is not to be
used for a long time.
Batteries contain chemical substances, so
they should be disposed of properly.
Using AC power
1 Check if the power/mains voltage, as shown
on the type plate located on the
bottom of the set, corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2 Connect the power cord to the
AC~ MAINS inlet and the wall socket.The
set is now ready for use.
3 To switch the set off completely, withdraw the
power cord from the wall socket.
4 Install the unit near the AC outlet and where
the AC power plug can be easily reached.
• Disconnect the power cord from the wall
socket to protect your set during heavy thun-
derstorms. Children could seriously injure
themselves as the free end of the cable may
still be live if only the connector is removed
from the MAINS socket at the back of the
unit.
The type plate is located on the
bottom of the set.
Auto power saving
• When the source selector is adjusted to
CD/USB and the set is in the PAUSE
position for 5 minutes, the set will be auto
switched to the stop position to save power.
• When the source selector is adjusted to
CD/USB and the set is in the STOP position
for 15 minutes, the set will be auto switched
to sleep (standby )mode. To wake it up,
press
2;.
Helpful hints:
– To avoid unnecessary energy consumption,
always adjust the source selector to OFF
after using the set.
CAUTION
- Visible and invisible laser radiation.
If the cover is open, do not look at
the beam.
- High voltage! Do not open.You run
the risk of getting an electric shock.
The machine does not contain any
user-serviceable parts.
- Modification of the product could
result in hazardous radiation of
EMC or other unsafe operation.
English Controls / Power Suppy Power Supply