Philips 27PT71B - Manual (Page 21)

21
4
PICTURE
SOUND
FEATURES
INSTALL
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
SLEEP
TV/VCR ON/OFF POSITION FREEZE
SWAP SOURCE
UP
SOUND PICTURE
MENU
CH
MUTE
PIP CH
SOURCE CC CLOCK
ITR/REC HOME HOME PERSONAL
VIDEO MOVIES
INCR. SURR.
PROGRAM LIST
SURF
OPEN/CLOSE
POWER
DN
A/CH
PIP
M LINK
VOL
STATUS/EXIT
TUNER A/B
OK
3
1
2
9
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
TIME
START TIME
STOP TIME
CHANNEL
TUNER MODE
ACCESS CODE
- - - -
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
ACCESS CODE
- - - -
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
ACCESS CODE
X X X X
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
ACCESS CODE
X X X X
INCORRECT TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
ACCESS CODE
- - - - TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
ACCESS CODE
X X X X
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
ENTER
NEW CODE
- - - - TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
ENTER
NEW CODE
X X X X TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
CONFIRM
CODE
- - - -
TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
CONFIRM
CODE
X X X X TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
CONFIRM
CODE
X X X X
CORRECT TIMER
AutoLock
PIP
CLOSED CAP
FORMAT
FEATURES
ACCESS CODE
- - - -
3
8
7
5
6
A
UTO
L
OCK
™ – S
ETTING
U
P THE
A
CCESS
C
ODE
NOTE TO PARENTS:
It isnÕt possible for
your child to unblock a
channel without know-
ing your access code or
changing it to a new
one. If your code has
been changed without
your knowledge, then
you will become aware
that blocked channels
may have been viewed.
A utoLock TM allows parents to
block out or ÒcensorÓ any
channels they think children should
not watch. A channel blocked by
the AutoLock
TM control cannot be
viewed until a correct access code
is used to unlock the channel for
viewing. First, letÕs set your
AutoLock access code.
Press the MENU button on
the remote control to show the
onscreen menu.
Press the CURSOR DOWN
button twice to highlight FEA-
TURES.
Press the CURSOR RIGHT
button and the menu will shift to
the left. Then press the CURSOR
DOWN button once to highlight
the AutoLock control.
Press the CURSOR RIGHT
button to highlight ACCESS
CODE.
Press 0,7,1,1 on the remote
control. INCORRECT will appear
on the screen.
Press 0,7,1,1 on the remote con-
trol again. ENTER NEW CODE
will appear on the screen.
Enter a new four-digit code
using the number buttons. CON-
FIRM CODE will appear on the
screen.
Enter your new four-digit
code again. CORRECT will flash
on the screen briefly and the high-
light bar goes back to AutoLock.
Press the STATUS/EXIT but-
ton to remove the menu from the
screen.
BEGIN
Remember that 0711 is the default
AutoLock
TM code. If your access code has
been changed by someone other than you
(a child, for example) or you have forgot-
ten the code, you can always get in by
inputting the default code.