Philips 26PF5320-28B User Manual
Page 2
Jack Panel Bottom of TV
AV I
NPUTS
T
he audio/video input jacks on the bottom panel of the TV are for
direct picture and sound connections between the TV and
a VCR (or similar device) that has audio/video output jacks.
1
Using an RCA type Video cable, connect one end of the cable to
the Video (yellow) Out jack on the VCR or accessory device
and
the other end to the AV Video In jack on the bottom of the TV.
NOTE: A S-Video cable can be used in place of the yellow video
cable if your device is equipped with an S-Video Output. S-Video
provides better video playback.
2
Using an RCA type Audio Left and Right cable, connect one end
to the left and right Audio Out L & R jacks (red & white) on the
VCR or accessory device
and the other ends to the AV Audio In L
& R jacks on the bottom of the TV.
3
Turn the VCR or accessory device and the TV On.
4
Press the AV+ button
on the remote control to show the Source
List menu on the TV screen.
5
Press the CURSOR DOWN button
repeatedly until AV is
highlighted, then press the CURSOR RIGHT button to enter the
selected Mode.
6
With the VCR (or accessory device) ON and a prerecorded tape
(CD, DVD, etc.) inserted, press the PLAY button to view the tape
on the television.
H
OOKING
U
P
THE
T
ELEVISION
C
OMPONENT
(CVI) I
NPUTS
3
2
R
EMOTE
C
ONTROL
B
ATTERY
To load the supplied battery into the remote:
1
Remove the plastic isolation sheet
from the battery compart-
ment door.
2
Point the remote control
at the remote sensor window on the
front of the television to operate the television.
If television does not respond to the remote control, check the
battery in the remote control:
1
Remove the battery compartment door
on the back of the
remote.
2
Check that the (+) end of the battery (3V)
face up correctly.
Reattach the battery compartment door.
H
OOKING
U
P
THE
T
ELEVISION
C
ABLE
/C
ABLE
B
OX
TV
Y
our Cable TV input into your home may be a single (75 ohm)
cable or use a cable box decoder. In either case the connection
is very simple. Follow the steps below to connect your cable signal
to your new television.
Direct Cable Connections:
Th is connection will supply Stereo sound to the TV.
1
Connect the open end of the round Cable Company
supplied cable
to the 75Ω input on the bottom of the
TV. Screw it down fi nger tight.
Cable Box (w/RF In/Outputs):
Th is connection will NOT supply Stereo sound to the TV. Th e
sound from the cable box will be mono.
1
Connect the open end of the round Cable Company
supplied cable
to the cable signal IN(put) plug on the
back of the Cable Box.
2
Using a separate round coaxial cable, connect one end to
the OUT(put) (TO TV) plug on the back of the Cable
Box
.
3
Connect the other end of the round coaxial cable
to the
75Ω input on the bottom of the television. Screw it down
fi nger tight.
NOTE:
Be sure to set the OUTPUT CHANNEL SWITCH
on the back of the cable box to CH 3 or 4, then tune the cable
box on the TV to the corresponding channel. Once tuned,
change channels at the cable box, not the television.
Cable Box (w/Audio/Video Outputs):
Th is connection will supply Stereo sound to the TV.
1
Connect the open end of the round Cable Company
supplied cable
to the cable signal IN(put) plug on the
back of the Cable Box.
2
Using an RCA type Video Cable, connect one end of the
cable to the Video (yellow) (or ANT, your cable box
may be labeled diff erently) Out jack on the cable box
and the other end to the Video In jack on the bottom of
the TV.
3
Using an RCA type Audio Left and Right Cable
, con-
nect one end to the left and right Audio Out L & R jacks
(red & white) on the cable box and the other ends to the
Audio In L & R jacks on the bottom of the TV.
NOTE:
Use the AV+ button and the CURSOR DOWN/
RIGHT on the TV remote control to tune to the AV channel
for the cable box signal. Once tuned, change channels at the
cable box, not the television.
A
NTENNA
TV
A
combination antenna receives normal broadcast channels
(VHF 2–13 and UHF 14–69). Your connection is easy
because there is only one 75Ω (ohm) antenna plug on the back of
your TV, and that’s where the antenna goes.
1
If your antenna has a round cable
(75 ohm) on the end,
then you’re ready to connect it to the TV.
If your antenna has fl at, twin-lead wire
(300 ohm), you
fi rst need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
2
Push the round end
of the adapter (or antenna) onto the
75Ω (ohm) plug on the bottom of the TV. If the round
end of the antenna wire is threaded, screw it down fi nger
tight.
C
omponent Video inputs provide the highest possible color and picture
resolution in the playback of digital signal source material, such as
with DVD players.
1
Connect the Component (Y, Pb, Pr) Video OUT
jacks from
the DVD player (or similar device) to the CVI-1 VIDEO Input
(Y green, Pb blue, Pr red) jacks on the bottom of the TV.
2
Connect the red and white AUDIO CABLES
on the rear of the
TV to the Audio (left and right) output jacks on the rear of the
accessory device.
3
Turn the TV and the DVD player (or digital accessory device)
ON.
4
Press the AV+ button
on the remote control to show the Source
List menu on the TV screen.
5
Press the CURSOR DOWN button
repeatedly until CVI-1 is
highlighted, then press the CURSOR RIGHT button to enter
the selected Mode.
6
Insert a DVD disc into the DVD player and press the PLAY π
button
on the DVD Player.
HD (H
IGH
D
EFINITION
) I
NPUTS
I
f you are using a High Defi nition receiver that can transmit high
defi nition programming, the TV can accept those signals through the
HD Inputs located on the bottom of the TV.
1
For Digital Connection, connect the HDMI connector of the
HD Receiver
(or similar device) to the HDMI Input jacks on
the bottom of the TV.
OR
2
For Analog Connection, use Component Video cables to con-
nect the Component (Y, Pb, Pr) Video Out jacks of the HD
Receiver
(or similar device) to the VGA adapter (supplied with
the TV). Connect the other end of the adapter to the VGA Input
jacks on the bottom of the TV.
3
Connect the red and white audio cable
to RCA type Audio
Cables. Connect the audio adapter to the PC Audio In L & R
jacks on the bottom of the TV.
4
Turn the TV and the HD Receiver ON.
5
Press the AV+ button
on the remote control to show the Source
List menu on the TV screen.
6
Press the CURSOR DOWN button
repeatedly until HDMI
(for digital connections) or CVI-2 (for analogue connections) is
highlighted, then press the s button to enter the selected mode.
NOTE:
Th e Audio/Video cables needed for this connection are not
supplied with your TV. Please contact your dealer or Philips at 1-888
PHILIPS (744-5477) for information about purchasing the needed
cables.
Be sure to point the remote
control at the remote sensor
window on the front of the
television when using the remote
control to operate the television.
Remote Control
(shown from the bottom)
Lithium Battery (3V)
Battery
Compartment
Door
Direct Cable Connection:
Cable signal coming from
Cable Company (Round
75Ω coaxial cable)
Jack Panel Bottom of TV
Cable Box with RF Inputs and Outputs Connection:
Jack Panel Back of Cable Box
Cable Box with Audio/Video Outputs Connection:
Cable Signal IN
from the Cable
Company
Audio Cables L & R
(Red, White)
Antenna Connection:
Outdoor or Indoor Antenna
(Combination VHF/UHF).
Th e combination antenna
receives normal broadcast
channels 2-13 (VHF) and
14-69 (UHF).
Twin Lead
Wire
Round 75Ω
Coaxial Cable
from Antenna
300 to 75-ohm
Adapter
AUDIO IN
(RED/WHITE)
VIDEO IN
(YELLOW)
VCR (or accessory device)
(EQUIPPED WITH VIDEO
AND AUDIO OUTPUT JACKS)
COMPONENT VIDEO
CABLES (Green, Blue, Red)
AUDIO CABLES
(RED/WHITE)
ACCESSORY DEVICE EQUIPPED WITH
COMPONENT VIDEO OUTPUTS.
HELPFUL HINT
Th e description for the component video connectors may diff er depending on the DVD player or accessory digital source
equipment used (for example, Y, Pb, Pr; Y, B-Y, R-Y; Y, Cr, Cb). Refer to your DVD player or digital accessory owner’s
manual for defi nitions and connection details.
Analog
Connection
COMPONENT
VIDEO CABLES
(Green, Blue, Red)
Digital
Connection
Rear of HD Receiver
(Illustration is for
reference only. Your
HD Receiver’s jack
panel may be labeled
diff erently.
Coxial Cable
Lead-in from
Cable Outlet,
Cable Converter
Box, or VHF/
UHF Antenna
Coaxial cable
Lead-in from
Satellite Dish
or Antenna
HD RECEIVER
EQUIPPED WITH
COMPONENT
VIDEO OUTPUTS.
AUDIO
CABLES
1
Jack Panel Bottom of TV
Cable Signal IN from
the Cable Company
Output Channel Switch
Round 75Ω
Coaxial Cable
1
3
2
Jack Panel Back of Cable
Box with A/V Outputs
Video Cable (Yellow)
1
3
Jack Panel Bottom of TV
1
2
Jack Panel Bottom of TV
3
6
CVI
TUNE
TO AV
CHANNEL
AV
Jack Panel
Bottom of TV
4
2
3
6
4
1
2
HDMI
5
1
2
3
6
6
4
1
2
5
5
5
5
NOTE: Th e plastic isolation sheet must be
removed for the remote control to function.
Plastic Isolation
Sheet
HDMI
CABLE
English