Liebherr G 1213 - Manual (Page 7)

4.6 Connecting the appliance
NOTICE
Risk of damage to the electronic control system!
u Do not use stand-alone inverters (conversion of d.c. to a.c./
three-phase) or energy saving plugs.
WARNING
Fire and overheating hazard!
u Do not use extension cables or multiple socket outlets.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It
must be outside the area of the rear of the appliance.
u Check the electrical connection.
u Plug in the power plug.
4.7 Switching on the appliance
u Press the On/Off button Fig. 3 (1) .
w The appliance is switched on. The temperature display and
Alarm symbol Fig. 3 (7) flash until the temperature is cold
enough.
w If “DEMO” is displayed, demo mode is activated. Please
contact the after sales service.
5 Control
5.1 Brightness of the temperature
display
You can adjust the brightness of the temperature display to the
light conditions of the room in which the appliance is installed.
5.1.1 Adjusting the brightness
The backlight can either be switched off or set to one of 5
levels. The backlight is switched off ex works.
u To activate the setting mode: Press the SuperFrost button
Fig. 3 (4) for about 5 seconds.
w The menu symbol Fig. 3 (6) shines and the child lock symbol
Fig. 3 (9) flashes.
u Press the setting button Fig. 3 (2) to select the brightness
function.
w The child lock symbol Fig. 3 (9) goes out and the brightness
symbol Fig. 3 (8) flashes.
u To confirm: Briefly press the SuperFrost button Fig. 3 (4) .
w The brightness symbol Fig. 3 (8) shines.
u Using the setting button Fig. 3 (2) , select either "off" or the
brightness wanted. The more display fields of the tempera-
ture display that light up, the brighter it is. If no field is lit up, it
means "off".
u To confirm: Press the SuperFrost button Fig. 3 (4) .
w The brightness symbol Fig. 3 (8) flashes.
w The brightness is adjusted to the new value.
u To deactivate the setting mode: Press the On/Off button
Fig. 3 (1) .
-or-
u Wait for 5 minutes.
w The brightness symbol Fig. 3 (8) and the menu symbol
Fig. 3 (6) go out.
w The temperature is indicated again in the temperature
display.
5.2 Child proofing
The child-proofing function enables you to make
sure that the appliance is not inadvertently switched
off by playing children.
5.2.1 To activate child lock
u To activate the setting mode: Press the SuperFrost button
Fig. 3 (4) for about 5 seconds.
w The menu symbol Fig. 3 (6) shines and the child lock symbol
Fig. 3 (9) flashes.
u Briefly press the SuperFrost button Fig. 3 (4) to select the
child lock function.
w The child lock symbol Fig. 3 (9) shines. The
-15 °C and -21 °C LEDs shine in the temperature
display.
u Briefly press the SuperFrost button Fig. 3 (4) to activate the
child lock.
w The child lock symbol Fig. 3 (9) flashes. The -15 °C and
-21 °C LEDs go out.
u To deactivate the setting mode: Press the On/Off button
Fig. 3 (1) .
-or-
u Wait for 5 minutes.
w The menu symbol Fig. 3 (6) goes out and the temperature is
displayed again in the temperature display. The child lock
symbol Fig. 3 (9) shines.
5.2.2 To deactivate child lock
u To activate the setting mode: Press the SuperFrost button
Fig. 3 (4) for about 5 seconds.
w The menu symbol Fig. 3 (6) shines and the child lock symbol
Fig. 3 (9) flashes.
u Briefly press the SuperFrost button Fig. 3 (4) to select the
child lock function.
w The child lock symbol Fig. 3 (9) shines. The
-18 °C LED shines in the temperature display.
u Briefly press the SuperFrost button Fig. 3 (4) to deactivate
the child lock.
w The child lock symbol Fig. 3 (9) flashes.
u To deactivate the setting mode: Press the On/Off button
Fig. 3 (1) .
-or-
u Wait for 5 minutes.
w The menu symbol Fig. 3 (6) goes out and the temperature is
displayed again in the temperature display. The child lock
symbol Fig. 3 (9) no longer shines.
5.3 Temperature alarm
The temperature display and the alarm symbol
Fig. 3 (7) flash at the same time.
The cause of the temperature being too high may be:
- warm fresh food was placed inside
- too much warm ambient air flowed in when rearranging and
removing food
- power failure for some time
Control
* Depending on model and options 7