Blaupunkt Sydney RCM 126 - Manual (Page 7)

Switching the audio source
Displaying the radio pass data
Using the supplied with your
set you can have the radio pass data such
as the model name, product number (7 6 . ..)
and serial number indicated on the display
panel.
Please refer to chapter “DSC programming
READ KC”.
Optical indication for extra
security
Turning off the blinking LED
When you insert your the LED is
automatically turned off until the card is re-
moved and the ignition turned off, assum-
ing the unit is connected as described in the
installation instructions.
If you do not want the tongue to blink at any
time, simply access “LED” in the DSC menu,
and press
or to turn in off.
Care of your
Using the SRC button you can switch be-
tween the following audio sources:
radio,
tape,
changer (optional), or AUX
Tape operation is only available if a cassette
is inserted.
AUX is only available if no Blaupunkt chang-
er CDC A05 or CDC A 071 is connected.
“AUX ON” must be activated in the DSC
menu.
Blinking tongue For a proper function of the it is
To switch to another source,
When the vehicle is stationary and the
important that the contacts are free from any
foreign particles. Avoid direct skin contact.
l
press SRC briefly.
Card removed, the tongue can be
switched to blink for extra anti-theft
If necessary, clean the contacts
rity.
using a cotton swab soaked with alcohol.
For this it is necessary that the positive pow-
er supply line and the permanent V lead
are connected such as described in the in-
stallation instructions.
Be sure that “LED ON” is adjusted in the
DSC mode.
If required, please refer to chapter “DSC
programming LED”.
Radio operation with RDS (Radio Data System)
is equipped to receive Radio Data
System or RDS signals. RDS is a
ary signal used by many FM radio stations
to broadcast additional information.
punkt has been a key player in developing
RDS in Europe.
This radio’s RDS features include program
service name (PS), which automatically dis-
plays RDS station’s identification such as
WNYC-FM or THE WAVE. Other RDS fea-
tures included are alternative frequency
switching (AF), program type identification
and search (PTY), and capability to receive
future Emergency Alert System (EAS) mes-
sage broadcasted by RDS stations. All are
explained in this section.
AF Alternative frequency
The AF (Alternative Frequency) function
makes sure that the strongest frequency of
the currently selected program is always
tuned in automatically.
This function is activated when
appears
in the display.
In order to switch this function on or off,
l
press the AF button briefly.
While searching for the strongest reception
signal, the radio may switch to mute briefly.
If “SEARCH” appears in the display when
switching on the radio or recalling one of the
14
stored frequencies, the unit is automatically
searching for an alternative frequency.
“SEARCH” will disappear from the display
when the alternative frequency has been
found or after the frequency band has been
run through completely.
If the reception quality of the selected pro-
gram becomes too bad:
l
Tune into another station.
Selecting a
With this car radio you can select between
the following wavebands:
Seek tuning
v D o w n
Down in
intervals
must be switched off)
Up in short intervals
must be switched off)
FM 87.5 107.9 MHz
Manual tuning with
l
Select the desired by
You can also tune in a station manually.
ing the FMT or AMT button.
Station tuning
Condition:
AF and PTY must be switched off (i.e. the
symbols do not light up in the display).
If necessary, deactivate these functions:
Automatic (seek) tuning A/V
l
Press or PTY.
l
Press A/V; the car radio will
search for the next station. Manual tuning:
When keeping the upper or lower part
l
of the rocker switch depressed, seek tuning
Press the frequency will change
will speed up in upwards or downwards
in short intervals in downwards or
wards direction.
When holding the right or left of the rock-
er switch down, the frequency movement is
speeded up.