Philips cortapelos para cortarte el pelo tú mismo - Manual (Page 2)

ENGLISH
Introduction
Dear customer, you have made the right choice! Your new
Philips hair clipper with new ergonomic design and 180°
adjustable cutting element allows you to clip your own
hair easily. You can move the clipper over all areas of your
head as easily as running your fingers through your hair.
To enjoy using the hair clipper, we advise you to read the
following information.
General description (Fig. 1)
A On/off slide
B Charging light
C Adapter (2.5V)
D Precision trimmer
E Cutting element
F Swivel head
G Length setting indication window
H Length selector
I Cleaning brush
J Large comb (13-21mm)
K Small comb (3-11mm)
Important
Read these instructions for use carefully before you use
the appliance and save them for future reference.
Check if the voltage indicated on the adapter
corresponds to the local mains voltage before you
connect the appliance.
Only use the adapter supplied to charge the
appliance.
The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
Do not use a damaged adapter.
If the adapter is damaged, always have it replaced by
one of the original type in order to avoid hazard.
Do not use the appliance when one of the
attachments is damaged or broken, as this may
cause injury.
Use, charge and store the appliance at a
temperature between 15°C and 35°C.
Keep the appliance and the adapter dry.
Keep the appliance out of the reach of children.
This appliance is only intended for clipping human
scalp hair. Do not use it for another purpose.
If the appliance is subjected to a major change in
temperature, pressure or humidity, let the appliance
acclimatise for 30 minutes before you use it.
Electromagnetic fields (EMF)
This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and in accordance with the instructions in this
instruction manual, the appliance is safe to use according
to scientific evidence available today.
Charging
A fully charged appliance has a cordless clipping time of
up to one hour.
Do not charge the appliance for more than 24 hours.
The ideal charging time is 8 hours.
1 Charge the appliance for 8 hours before you use it
for the first time.
Make sure the appliance is switched off when you charge
it.
2 Insert the appliance plug into the appliance and
insert the adapter into the wall socket. (Fig. 2)
The charging light goes on to indicate that the
appliance is charging.
Note:The charging light does not indicate when the
appliance is fully charged.
Corded clipping
Only run the appliance from the mains when the
battery is empty.
1 Switch off the hair clipper.
2 Connect the hair clipper to the mains and wait a
few seconds before you switch it on.
,
,
,
,
,
,
,
,
,
,
,
,
If the batteries are completely empty, wait a few minutes
before you switch on the appliance.
Using the appliance
Make sure your hair is clean and dry. Do not use the
appliance on freshly washed hair.
1 Comb your hair with a styling comb in the
direction of hair growth. (Fig. 3)
Clipping with comb attachment
Use the small or large comb attachment, depending
on the desired hair length. The remaining hair
length after cutting is indicated in mm on the comb
attachments. The selected hair length setting (1-5) is
shown in the two length setting indication windows
on both sides of the length selector. (Fig. 4)
See the table below for an overview of the length
settings and the corresponding hair lengths of each comb
attachment.
Small
comb
Large
comb
setting hair length setting hair length
1 3mm/
0.12in
1 13mm/0.51in
2 5mm/
0.20in
2 15mm/0.59in
3 7mm/
0.28in
3 17mm/0.67in
4 9mm/
0.35in
4 19mm/0.75in
5 11mm/
0.43in
5 21mm/0.83in
1 Slide the comb attachment into the guiding grooves
of the appliance (‘click’). (Fig. 5)
Make sure that the comb attachment has been properly
slid into the grooves on both sides.
2 Set the comb attachment to the desired hair length.
To do this, press the release button on the length
selector (1) and turn it to the left or right (2). (Fig.
6)
Do not turn the length selector beyond the highest hair
length setting (5).
3 Switch on the appliance.
Using the swivel head
From its starting position of 0° (pointing forwards),
you can turn the swivel head 45° or 90° to the left
or right. In this way, you can adjust the position of
the cutting element to the part of your head you
are clipping. This makes it much easier to clip your
own hair. (Fig. 7)
1 Set the cutting element to the desired position by
turning the swivel head (‘click’). (Fig. 8)
Always adjust the position of the cutting element with
the swivel head. Do not turn the cutting element or the
comb.
Do not turn the swivel head more than 90° to the left
or right.
The swivel head allows you to hold and use the
appliance like a brush. (Fig. 9)
Tips
We advise you to start clipping at the highest setting
of the large comb and to reduce the hair length
setting gradually.
If a lot of hair has accumulated in the comb
attachment, remove it from the clipper and blow
and/or shake the hair out of it. When you remove
the comb attachment, the hair length setting does
not change.
Write down the hair length settings you use to
create a certain hairstyle as a reminder for future
clipping sessions.
1 Move the clipper through the hair slowly.
,
,
,
-
-
-
The hair on different parts of your head grows in
different directions. You may want to try different
clipping directions (upwards, downwards and
across). (Fig. 10)
To clip in the most effective way, move the
appliance against the direction of hair growth.
2 Turn the swivel head to the position that is most
comfortable for your arm when clipping the
different parts of your head.
3 Make sure that the flat part of the comb
attachment is fully in contact with the scalp to
obtain an even cutting result.
Clipping without comb attachment
You can use the clipper without comb attachment to clip
your hair very close to the skin (0.8mm) or to contour
the neckline and the area around the ears.
Note:When you use the hair clipper without a comb
attachment, the clipper cuts the hair very close to the skin.
1 Remove the comb attachment by pulling it off the
appliance. (Fig. 11)
Never pull at the flexible top of the comb attachment.
Always pull at the bottom part.
2 When you contour the hair around the ears, only
cut the hair ends. The hairline should be close to
the ear. (Fig. 12)
3 To contour the neckline and the sideburns, turn the
clipper and make downward strokes. (Fig. 13)
4 Move slowly and smoothly. Just follow the natural
hairline.
5 Adjust the position of the swivel head to make
contouring easier.
Using the precision trimmer
You can use the appliance with the precision trimmer to
contour the neckline and the area around the ears more
easily and more precisely.
1 Make sure the appliance is switched off.
2 Remove the comb attachment. (Fig. 11)
3 Apply pressure to the centre of the cutting element
to open it. (Fig. 14)
4 Place the lug of the precision trimmer into the
slot and push the cutting element back onto the
appliance (‘click’). (Fig. 15)
Cleaning
Do not use abrasives, scourers or liquids such as
alcohol, petrol or acetone to clean the appliance.
Only clean the appliance and the adapter with the brush
supplied.
Be careful that the cutting element does not fall on the
floor.
1 Clean the appliance every time you have used it.
2 Make sure the appliance is switched off and
disconnected from the mains before you clean it.
3 Remove the comb attachment. (Fig. 11)
4 Apply pressure to the centre of the cutting element
to open it. (Fig. 14)
5 Clean the cutting element with the brush supplied.
(Fig. 16)
6 Clean the appliance with the brush supplied. (Fig.
17)
7 Close the cutting element by pushing it back onto
the appliance (‘click’). (Fig. 18)
The appliance does not need any lubrication.
Replacement
Only replace a worn or damaged cutting element with an
original Philips cutting unit.
Environment
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an official collection point for recycling. By doing
this, you help to preserve the environment. (Fig. 19)
,
,
,
4203.000.5531.1 2/7