General directions for use – Bahco Sandflex Holesaw Sets User Manual
Page 7
•
Selection of arbor. Select the proper arbor for the holesaw
size and your power drill. If the arbor has drive pins, make
sure they are engaged. For arbors with drive pins, slide pin
ring back, screw holesaw onto arbor to shoulder, and push
ring with pins into holesaw while backing off holesaw if
necessary.
•
Feed rate. Maintain positive feed rate, and always start
cutting square to the workpiece.
•
Removal of chips. Chip removal is extremely important.
Withdraw holesaw intermittently to prevent clogging.
•
Operation speed. The cutting speeds recommended can
be found in the instructions leaflet in the Holesaw Sets.
Variations from these recommendations may be chosen
from your own experience.
•
Lubricants. Always use a lubricant when cutting metal,
as this increases the life of the holesaw.
General directions for use
EAN code: 731151 8044985
Holesaws
3830-16-VIP
16 mm
5/8"
3830-22-VIP
22 mm
7/8"
3830-25-VIP
25 mm
1"
3830-29-VIP
29 mm
1 1/8"
3830-32-VIP
32 mm
1 1/4"
3830-41-VIP
41 mm
1 5/8"
3830-51-VIP
51 mm
2"
3830-73-VIP
73 mm
2 3/4"
3830-83-VIP
83 mm
3 1/4"
Arbors
3834-ARBR-930
– for holesaws 14 – 30 mm
3834-ARBR-9100 (PD type)
– for holesaws 30 – 100 mm
Set 3834-SET-92
EAN code: 731151 8166458
Holesaws
3830-16-VIP
16 mm
5/8"
3830-19-VIP
19 mm
3/4"
3830-25-VIP
25 mm
1"
3830-30-VIP
30 mm
1 3/16"
3830-35-VIP
35 mm
1 3/8"
3830-41-VIP
41 mm
1 5/8"
3830-51-VIP
51 mm
2"
3830-67-VIP
67 mm
2 5/8"
Arbors
3834-ARBR-1130
– for holesaws 14 – 30 mm
3834-ARBR-11152 (PD type)
– for holesaws 30 – 210 mm
Set 3834-SET-94
EAN code: 731151 8159894
Holesaws
3830-16-VIP
16 mm
5/8"
3830-19-VIP
19 mm
3/4"
3830-22-VIP
22 mm
7/8"
3830-29-VIP
29 mm
1 1/8"
3830-35-VIP
35 mm
1 3/8"
3830-44-VIP
44 mm
1 3/4"
3830-52-VIP
52 mm
2 1/16"
3830-57-VIP
57 mm
2 1/4"
3830-64-VIP
64 mm
2 1/2"
Arbors
3834-ARBR-1130
– for holesaws 14 – 30 mm
3834-ARBR-11152 (PD type)
– for holesaws 30 – 210 mm
3834-DRL
Set 3834-SET-95
Space prepared for 3 extra holesaws
PCS
MM
INCH
from
to
from
to
1 x
19
20
3/4
25/32
1 x
32
35
1 1/4
1 3/8
1 x
37
40
1 7/16
1 9/16
Space prepared for 3 extra holesaws
PCS
MM
INCH
from
to
from
to
1 x
32
–
1 1/4
–
1 x
37
40
1 7/16
1 9/6
1 x
37
83
1 7/16
3 1/4
Space prepared for 3 extra holesaws
PCS
MM
INCH
from
to
from
to
1 x
19
25
3/4
1
1 x
32
–
1 1/4
–
1 x
37
40
1 7/16
1 9/6
07-0016_Holesaws_UK
07-05-21, 14.04
7