Pioneer CMX-3000 - Manual (Page 20)

20
Published by Pioneer Corporation.
Copyright © 2001 Pioneer Corporation.
All rights reserved.
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
Multimedia and Mass Storage Division:
2265 East 220th Street, Long Beach, CA 90810, U.S.A. TEL: 800-444-OPTI (6784)
PIONEER ELECTRONICS OF CANADA, INC.
Industrial Products Department:
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 905-479-4411
Printed in
Appendix (Troubleshooting)
Error Message Display
When the CMX-3000 CD player is unable to operate properly, an error code is displayed on the display panel. Check the error code
displayed against the following table and take the recommended action to correct the error. If an error code other than any of the
error codes listed in the table below is displayed or if the same error code is displayed even after corrective action has been taken,
contact your nearest Pioneer Service Station or contact the store from which you purchased your player for assistance.
Error Code
E-7201
E-83 01
E-83 02
E-83 03
E-91 01
Description
Player unable to read TOC data.
Player unable to play back currently
inserted disc.
Mechanical operation has failed to
complete within specified time
interval.
Possible cause and recommended action
Disc is cracked.
= Recommended action: replace disc.
Disc is soiled or dirty.
= Recommended action: clean disc.
If other discs play normally, the problem is
with the disc itself.
Dust or some other form of foreign particles
have found their way into disc insertion slot.
= Recommended action: remove dust or
other foreign particles.
Error Type
TOC READ ERROR
PLAYER ERROR
MECHANICAL TIME
OUT
Cleaning the Jog Dial
To clean the PLAYER wipe with a polishing or a soft, dry cloth. For
stubborn dirt, moisten a soft cloth with a weak solution of neutral
detergent (diluted in five to six parts water), wring the cloth well,
and wipe away the dirt. Use a dry cloth to wipe the surface dry.
Applying alcohol, paint thinner, benzene, insecticides, or other
stringent substances to the jog dial may cause the markings or
finishing of the dial to peel or become discolored, and the use of
any such substances should accordingly be avoided.
300 Allstate Parkway
Markham, ON L3R OP2
(905) 479-4411
1 (877) 283-5901
For warranty information please see the Limited Warranty
sheet included with your product.
Should this product require service in Canada, please contact a
Pioneer Canadian Authorized Dealer to locate the nearest Pio-
neer Authorized Service Company in Canada.
Alternatively, please contact the Customer Service Department
at the following address:
Pioneer Electronics of Canada, Inc.
Should this product require service in the U.S.A. and you wish
to locate the nearest Pioneer Authorized Independent Service
Company, or if you wish to purchase replacement parts,
operating instructions, service manuals, or accessories, please
call the number shown below.
800 – 872 – 4159
Please do not ship your product to Pioneer without first calling
the Customer Support Division at the above listed number for
assistance.
PIONEER ELECTRONICS (USA) INC.
CUSTOMER SUPPORT DIVISION
P.O. BOX 1760, LONG BEACH,
CA 90801-1760, U.S.A.
For warranty information please see the Limited Warranty
sheet included with your product.
÷ There may be times when the CMX-3000 fails to operate properly as a result of static electricity or some other form of interference from an outside
source. If any such problem occurs, turn off the power to the CMX-3000, wait for the currently inserted disc to come to a full stop, and then turn on
the power again to see if that fixes the problem in question.
÷ The CMX-3000 cannot be used to replay partially-written CD-R or CD-RW discs.
÷ The CMX-3000 cannot be used to replay non-standard-shaped discs or any discs other than 5 inch/12 cm discs or 3 inch/8 cm discs which have been
inserted into an 3 inch/8 cm disc adapter. (Note that attempting to replay such discs may result in damage or breakdown.)
÷ The BPM value measured by the CMX-3000 may differ from the BPM value recorded on a CD or from our DJ mixer, but this difference is a result of
differences in the BPM value measurement method; not a result of a fault with the player.