Scarlett SC-1166 User Manual
Page 3
www.scarlett-europe.com
SC-1166/1167/1168
3
GB
INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
· Please read all the instruction manual before use and save it for future references.
· Before first switching on check that voltage indicated on the rating label, corresponds with the mains voltage in your home.
· For home use only. Do not use for industrial purposes. Use the oil heater only for its intended use.
· Do not use outdoors or in damp area.
· Do not immerse the oil heater and the cord in water or other liquids.
· Never pull the cord while disconnecting from the power outlet; instead, grasp the plug only and pull to disconnect.
· Do not allow the cord to touch sharp edges and hot surfaces.
· Always unplug appliance from the power supply when not in use.
· Do not operate the appliance with damaged cord or plug, or after the appliance malfunctions, or has been dropped or damaged in any manner. To
avoid the risk of electric shock, do not disassemble the oil heater; take it to a service center for examination, repair or mechanical adjustment.
· Close supervision is necessary when the appliance is used near children.
· Do not leave appliance unattended while operating.
· The oil heater must be used only in the upright position.
· Unit surface temperature of the appliance is high, thus do not touch it, except the handle.
· Operating unit should be far away from the flammable or easy bulging under high temperature objects.
CAUTION:
· To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
· Do not cover the appliance when in use.
ASSEMBLING
· First turn the unit upside-down.
· Install multidirectional rolling wheels to each end between the first and the second groups of the heating
flanges.
· Let the
shape screw surround the dome of the heating flanges. Then insert it into two holes of the
supporting plate.
· Use butterfly nuts to screw them tightly counterclockwise.
· Place heater normally and make sure that it is inconvertible.
USING THE APPLIANCE
· Set thermostat to minimal position and power switch to position, plug in the appliance.
POWER SELECTOR
· You can adjust oil heater current power using power regulator:
Off;
Minimum power;
II
Medium power;
III
Maximum power.
THERMOSTAT
· Set thermostat to maximum position.
· When the temperature rises to satisfying level, slowly turn the thermostat counterclockwise until the indicator light is out, and the room temperature
thus can keep constant.
· If you want to change the room temperature, you can make another regulation: turn the thermostat clockwise to arise the temperature and
counterclockwise to lower it.
· When the temperature is below than thermostat set value, heating element will switch on and indicator will light.
NOTE:
· The room must be properly sealed, if not, using of oil heater will not make good result because of heat leakage.
· After use, turn the power selector to the position, then turn the thermostat to the minimum position and unplug from power supply.
CLEAN AND CARE
· The oil heater should be cleaned regularly to wipe out the dust on the surface of fins. As this may result the radiating efficient.
· Unplug from the power supply and allow the appliance to cool down.
· Wipe out with a soft damp cloth. Do not use detergent or abrasives.
· Do not scrap the surfaces of fins with sharp hard tools, to avoid surfaces getting rusty, because of damage of the paint coat.
STORAGE
· Switch off and unplug the appliance. Ensure the oil heater is completely cool.
· Complete all requirements of chapter CLEAN AND CARE.
· Reel on the power cord.
· Keep the appliance in a dry cool place.
RUS
·
.
,
.
·
,
,
,
.
·
.
.
·
.
·
.
·
,
.
·
,
.
·
,
.
·
,
,
.
,
.
·
.
·
.
·
.
·
,
.
·
.
:
·
,
.
·
.