AEG DAB 4138 schwarz - Manual (Page 41)

English
41
NOTE:
• You cannot toggle between Mono and Stereo during
DAB reception.
• To manually set a DAB frequency, proceed as de-
scribed in the “Settings menu” section.
Display additional DAB information
In DAB mode, you can display the following additional infor-
mation if broadcast by the radio station. To do so, press the
INFO button (7).
The DLS text is shown on the display by default.
• DLS: Short for
Dynamic Label Segment. This involves
complementary data. This content may be e.g. informa-
tion about the station or the music title and artist being
played.
• Displays the received signal strength.
• This indicates the station category (e.g. Pop-Music, News
etc.).
• Displays the name of the station group (e.g. DR Deutsch-
land).
• Frequency of the current radio station.
• The “SIGNAL ERROR” display shows the signal quality.
The lower the adjacent figure, the better the quality.
• Displays the digital Audio Bit Rate.
• Display the time.
• Display the date.
Save station
1. If you have found the desired station, hold down the
PRESET button (12). The first preset location appears on
the display. If the preset location is still empty the word
EMPTY appears under PRESET STORE.
2. For choosing the memory position, please press /
buttons (3).
3. Press REPEAT ALARM/SELECT to save the settings.
Select a preset station
1. Press the PRESET button (12).
2. Press the / buttons (3) to chose a memory position.
3. Confirm your selection with the REPEAT ALARM/SELECT
button (9).
Settings menu
Numerous settings are made via the Settings menu (see
page 5).
In the Settings menu you can find the main menu and the
related submenus with the individual options.
To open the menu, press the MENU button (6) during opera-
tion.
• Use the / buttons (3) to navigate in the menu.
• Use the REPEAT ALARM/SELECT button (9) to select a
submenu, or confirm a setting.
• To exit the menu, press the MENU button (6).
NOTE:
• If you do not press any button within 30 seconds, the
menu is hidden.
• The currently set option is highlighted by “*“.
A Settings menu can be found in DAB mode, as well as in FM
mode. The DAB and FM menu is explained below along with
the general SYSTEM menu.
DAB Menu
The DAB menu is divided into menus: Full scan, Manual tune,
DRC and Prune.
•
Full scan: Starts the station scan. The DAB frequency
band is scanned for stations.
• Manual tune: To do so you need to know the station
frequency. This can be found on the internet site of the
broadcasting service. Select individual frequencies using
the / buttons (3).
• DRC: short for Digital Range Control (dynamic range).
The term DRC describes the ratio between the quietest
and the loudest sound. If the dynamic range is very high
there are very soft sounds as well as very loud sounds.
Under some circumstances this may present a problem
with playback. Let us assume that you are listening to a
radio station in a relatively loud environment. By increas-
ing the volume you can play the quiet sections louder.
This however has the disadvantage that the loud sections
become uncomfortably loud. It makes sense here to
reduce the dynamic range. Select between the options:
-
DRC off: The dynamic range is not reduced.
- DRC high: The dynamic range is sharply reduced.
- DRC low: The dynamic range is slightly reduced.
• Prune: It may be that you can no longer receive some
stations after a station scan or change of location. With
this function you can delete these stations from the
reception list. Select “YES” and confirm with the REPEAT
ALARM/SELECT button.
FM Menu
•
Scan setting: Select the desired option in order to per-
form an automatic station scan.
-
Strong stations only: Only search for strong radio
stations.
- All stations: Search for all receivable radio stations. In
doing so, the scan also pauses on weak stations.
• Audio setting:
-
Forced mono: Every radio station is played back in
mono irrespective of the transmitted signal.