AEG WS 24-180 - Manual (Page 14)

Deutsch
12
EN
English
b) Operations such as polishing are not recommended to be
performed with this power tool.Operations for which the power
tool was not designed may create a hazard and cause personal injury.
c) Do not use accessories which are not specifically designed
and recommended by the tool manufacturer. Just because the
accessory can be attached to your power tool, it does not assure safe
operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and fly apart.
e) The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled.
WARNING!
Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future reference.
ANGle GRINDeR SAfeTy WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush or cut-off tool. Read all safety warnings,
instructions, illustrations and specifications provided with
this power tool.Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
TeCHNICAl DATA
Angle Grinder
WS 22-180 WS 22-230 WS 24-180 V WS 24-230 V
Rated input 2200 W 2200 W 2400 W 2400 W
Rated speed 8500 min -1 6600 min -1 8500 min -1 6600 min -1
D= Grinding disk diameter max.
d= Grinding disk hole diameter
D
b
d
b= Cutting disk thickness min. / max.
180 mm
22,2 mm
1,5 / 3 mm
230 mm
22,2 mm
1,9 / 3 mm
180 mm
22,2 mm
1,5 / 3 mm
230 mm
22,2 mm
1,9 / 3 mm
D
b
d
b= Grinding disk thickness max. 6 mm 6 mm 6 mm 6 mm
D
D= Grinding surface diameter max. 180 mm 230 mm 180 mm 230 mm
D
D= Wiring brush diameter max. 100 mm 100 mm 100 mm 100 mm
Thread of work spindle M 14 M 14 M 14 M 14
Weight according EPTA-Procedure 01/2003 5,1 kg 5,2 kg 5,2 kg 5,4 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
96,0 dB(A)
107,0 dB(A)
96,0 dB(A)
107,0 dB(A)
96,0 dB(A)
107,0 dB(A)
96,0 dB(A)
107,0 dB(A)
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Surface grinding: Vibration emission value a
h;SG
Uncertainty K=
8,7 m/s 2
1,5 m/s 2
8,7 m/s 2
1,5 m/s 2
8,7 m/s 2
1,5 m/s 2
8,7 m/s 2
1,5 m/s 2
Disk sanding: Vibration emission value a
h;DS
Uncertainty K=
4,1 m/s 2
1,5 m/s 2
4,1 m/s 2
1,5 m/s 2
4,1 m/s 2
1,5 m/s 2
4,1 m/s 2
1,5 m/s 2
For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running
but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.