Asus A8N-E - Manual (Page 41)

A S U S A 8 N - E A S U S A 8 N - E A S U S A 8 N - E A S U S A 8 N - E A S U S A 8 N - E 1 - 2 9 1 - 2 9 1 - 2 9 1 - 2 9 1 - 2 9
A8N-E
®
A8N-E System panel connector
* Requires an ATX power supply.
F_PANEL
PLED- PWR PLED+
Ground
GND
Reset
IDE_LED+ IDE_LED-
IDE_LED RESET
PLED PWRSW
NC
1 3 . 1 3 . 1 3 . 1 3 . 1 3 . System panel connector (10-1 pin F_PANEL1) S y s t e m p a n e l c o n n e c t o r ( 1 0 - 1 p i n F _ P A N E L 1 ) S y s t e m p a n e l c o n n e c t o r ( 1 0 - 1 p i n F _ P A N E L 1 ) S y s t e m p a n e l c o n n e c t o r ( 1 0 - 1 p i n F _ P A N E L 1 ) S y s t e m p a n e l c o n n e c t o r ( 1 0 - 1 p i n F _ P A N E L 1 )
This connector supports several chassis-mounted functions.
• S y s t e m p o w e r L E D ( 2 - p i n P L E D ) S y s t e m p o w e r L E D ( 2 - p i n P L E D ) S y s t e m p o w e r L E D ( 2 - p i n P L E D ) S y s t e m p o w e r L E D ( 2 - p i n P L E D ) S y s t e m p o w e r L E D ( 2 - p i n P L E D )
This 3-pin connector is for the system power LED. Connect the
chassis power LED cable to this connector. The system power LED
lights up when you turn on the system power, and blinks when the
system is in sleep mode.
• A T X p o w e r b u t t o n / s o f t - o f f b u t t o n ( 2 - p i n P W R S W ) A T X p o w e r b u t t o n / s o f t - o f f b u t t o n ( 2 - p i n P W R S W ) A T X p o w e r b u t t o n / s o f t - o f f b u t t o n ( 2 - p i n P W R S W ) A T X p o w e r b u t t o n / s o f t - o f f b u t t o n ( 2 - p i n P W R S W ) A T X p o w e r b u t t o n / s o f t - o f f b u t t o n ( 2 - p i n P W R S W )
This connector is for the system power button. Pressing the power
button turns the system on or puts the system in sleep or soft-off
mode depending on the BIOS settings. Pressing the power switch for
more than four seconds while the system is ON turns the system OFF.
• H a r d d i s k d r i v e a c t i v i t y L E D ( 2 - p i n I D E L E D ) H a r d d i s k d r i v e a c t i v i t y L E D ( 2 - p i n I D E L E D ) H a r d d i s k d r i v e a c t i v i t y L E D ( 2 - p i n I D E L E D ) H a r d d i s k d r i v e a c t i v i t y L E D ( 2 - p i n I D E L E D ) H a r d d i s k d r i v e a c t i v i t y L E D ( 2 - p i n I D E L E D )
This 2-pin connector is for the HDD Activity LED. Connect the HDD
Activity LED cable to this connector. The IDE LED lights up or flashes
when data is read from or written to the HDD.
• R e s e t b u t t o n ( 2 - p i n R E S E T ) R e s e t b u t t o n ( 2 - p i n R E S E T ) R e s e t b u t t o n ( 2 - p i n R E S E T ) R e s e t b u t t o n ( 2 - p i n R E S E T ) R e s e t b u t t o n ( 2 - p i n R E S E T )
This 2-pin connector is for the chassis-mounted reset button for
system reboot without turning off the system power.