Audiovox APS-995 - Manual (Page 18)

18
TIMED START PROGRAM:
The Remote Start unit has the ability to start the vehicle automatically at timed intervals. This feature is
useful in extremely cold climates where starting the engine is the only means to keep the battery charged
and fluids warm. The operator has the option to have the unit start every 2 or 4 hours for a maximum of 48
hours. Factory pre-set is to start at 4 hour intervals. To select 2 or 4 hour automatic start timer:
1. Start with the Enable switch (Red Handle) in the "On" Position.
2. Turn the ignition on then off.
3. Within 10 seconds of the key turning off, cycle the enable switch Off, On, Off, On ( 2 times) to select a
2 hour timed start interval. Cycle the enable switch Off, On, Off, On, Off, On, Off, On (4 times) to select a
4 hour timed start interval. The lights will flash and the siren will chirp 2X or 4X dependent upon 2 or 4 hour
interval setting.
NOTE: Once selected, 2 or 4, this timer interval will remain in memory until it is manually changed. To
change, the above sequence will have to be followed.
TIMED START OPERATION:
To begin the start timer, within 10 seconds of turning off the ignition switch, activate the RF command to
start 2 times. (Press the start button four times). The lights will flash and the siren will chirp 4 times.
Indicating timed interval mode has been initiated. The vehicle will automatically start every 2 or 4 hours as
programmed. To cancel the timed start mode start the vehicle either by RF or by the ignition key.
REMOTE START SELECTABLE FEATURES
Feature LtsFlash 1X Lts Flash 2X Lts Flash 3X Lts Flash 4X Default LED Pattern
1 RF Start Chirp Off On On 1X Pause,etc...
2 Run Time 5 Min. 10 Min. 15Min. 20 Min. 10 Min 2X Pause,etc...
3Park Lights On Steady Flash Steady 3X Pause,etc...
4 Input Check NA Tach Tach 4X Pause,etc...
5 Check Level NA NA NA NA ------ 5X Pause,etc...
6 Ign. 2 Crank Off On On 6X Pause,etc...
7 Diagnostics Off On Off 7X Pause,etc...
8 Level NA NA NA NA NA 8X Pause,etc...
9 Gas/Diesel Gas Diesel 10 Diesel 15 Diesel 20 Gas 9X Pause,etc...
10 Trans.O/P While RS On During Start Until Ign Off While RS 10X pause,etc
NOTE:
When selecting Diesel operation, (Feature Nine), over gasoline, the only change is to the ignition circuits.
When Diesel is selected, the ignition circuits will power up 10, 15, or 20 seconds before the start circuit.
The intent of this feature is to allow the glow plug warming required by some diesel engines. If your vehicle
is a instant start diesel, it is not necessary to activate this feature.
NOTE: When selecting Diesel mode, be certain that the intended vehicle has a true tach reference and be
certain to connect the tach input wire.
To Program The Remote Start Selectable Features:
1. Turn the ignition key to the On position.
2. Press and release the valet/program switch three times.
3. Immediately turn the ignition key Off then press transmitter start button for 1 second.
4. Immediately turn the ignition key back On.
5. Press and release the valet/program switch two times. The siren will emit 2 short and 1 long chirp
verifying you are in the feature program mode.
6. Use channel 1 button on the transmitter to advance to the feature you want to change. EXAMPLE- If
you need to change selectable feature 3, press and release channel 1 button on the transmitter 3 times
in succession. The parking lights will flash and the siren will chirp 3 times confirming that selected
feature 3 can be changed.
7. Use the start button on the transmitter to change the selection of the programmable feature. If you are
not sure what the setting for any feature is, press the start button one time, the parking lights will flash
once or twice indicating the features setting.