Silverline Air Cut-Off Tool - Manual (Page 5)

Noise and Vibration
• Sound and vibration levels in the specification are determined according
to ISO 28927-3. The figures given can be used to compare similar tools
tested to this standard. These figures may be used to assess exposure to
noise and vibration levels.
• The figures represent normal use for the tool in normal working
condition. A poorly maintained, incorrectly assembled or misused tool
may produce increased levels of noise and vibration. The total working
period that you can operate this tool must factor in periods where the
tool is idle or switched off. Allow frequent rest breaks when operating
this tool.
• It is in the interest of users to maximise their safety using the correct
safety equipment, like ear defenders that protect against loud or
repetitive noise, and anti-vibration gloves that minimise vibration.
Do not operate the tool with your hands below a normal comfortable
temperature, as vibration will have a greater effect.
Sound
• The noise directive was introduced to protect against the risk to health
and safety arising or likely to arise from exposure to noise and risk of
hearing. The Directive can be used to define noise exposure and the
physical parameters, such as peak sound pressure and daily and weekly
exposure level. Particular attention should be taken to exposure level
and duration.
• For more information on the Noise Directives 2003/10/EC and 2000/14/
EC, please visit The European Agency for Safety and Health at work -
www.osha.europa.eu.
Vibration
• The European Physical Agents (Vibration) Directive 2002/44/EC was
introduced to control the exposure of vibration at work. The Directive
enables users of tools to make informed decisions on the amount of time
spent working. Those who regularly operate high vibration equipment
over a sustained period of time are at a higher risk of health problems.
ISO 28927-3 measures vibration in three directions which is known as
tri-axial or vector sum measurement. When operating high vibration
equipment, ensure not to exceed exposure levels. For more details on
The Vibration Directive 2002/44/EC please visit The European Agency for
Safety and Health at work -
www.osha.europa.eu
General Safety Warnings
• For multiple hazards, read and understand the safety instructions before
installing, operating, repairing, maintaining, changing accessories on, or
working near this tool. Failure to do so can result in serious bodily injury
• Only qualified and trained operators should install, adjust, or use this tool
• Do not modify this tool. Modifications can reduce the effectiveness of
safety measures and increase the risks to the operator
• Do not discard the safety instructions; give them to the operator
• Do not use this tool if it has been damaged
• Tools shall be inspected periodically to verify that the ratings and
markings required by this part of ISO 11148 are legibly marked on
the tool. The employer/user should contact the manufacturer to obtain
replacement marking labels when necessary
WARNING: This appliance is not intended for use by persons (including
children) with reduced, physical or mental capabilities or lack of experience
or knowledge unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the
appliance.
Projectile Hazards
• Be aware that failure of the workpiece or accessories, or even of the
inserted tool itself, can generate high-velocity projectiles
• Always wear impact-resistant eye protection during operation of this tool.
The grade of protection required should be assessed for each use
• For overhead work, wear a safety helmet
• The risks to others should also be assessed at this time
• Ensure that the workpiece is securely fixed
• Entanglement Hazards
4
GB
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction Manual
DO NOT use with compressed gas cylinders!
Conforms to relevant legislation and safety standards
Environmental Protection
Air tools must not be disposed of with household waste. Air
tools may contain traces of tool oil and other lubricants and so
must be recycled accordingly
Specification
Maximum operating pressure: ........................... 6.3bar (90psi)
Air consumption: ............................................... 170L/min (6cfm)
Air inlet: ............................................................. ¼" BSP, supplied with
two male airline quick connectors (EN-6 ‘UK’ and EQ-4 ‘European’ types)
Minimum hose diameter:................................... 9.5mm (
3 ⁄
8
")
No load speed: .................................................. 20,000min -1
Disc dimensions: ............................................... 75 x 10 x 2mm
(3" discs)
Angle: ................................................................ 0°
Spindle thread: .................................................. M6 (female)
Weight ............................................................... 0.77kg
Noise and vibration information:
Level of sound pressure according to Machinery directive 2006/42/EC:
Sound pressure: ............................................... L
PA
= 84dB(A)
Sound power: ................................................... L
WA
= 95dB(A)
Uncertainty: ....................................................... K = 3dB
The sound intensity level for the operator may exceed 85dB(A) and
sound protection measures are necessary.
Vibration total values (triax vector sum) according to Machinery directive
2006/42/EC:
Vibration emission value: ..................................
ah = 1.68m/s 2
Uncertainty: ....................................................... K = 1.5m/s 2
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
598446_Z1MANPRO1_new.indd 4 11/09/2013 10:56