Cencorp 1300 BR - Manual (Page 2)

CENCORP 1300 BR
TECHNICAL DATA
Pick & Place Work Envelope
Accuracy
Graphical User Interface
Router Work Envelope
Machine Vision
Software Options
Pick & Place Performance
External Vacuum System
Basic features
Board Handling (panel)
Gripper System
Machine Dimensions
Other
Electrical Service Requirements
Pneumatics Service Requirements
Output conveyor and other solutions
Environmental Requirements
Width: 1300mm
Centering unit on rear conveyor rail, program-
mable 2
nd locating pin: Optional
Correction of PCB position: Optional
Pressure: 5-7 bar
Flat belt conveyor: 1500mm x 250mm
Operating temperature: 10 ... 40°C
Depth: 1900mm
Ionizer: Optional
Downward looking camera: Optional
±10%, dry clean air
Tray conveyor: tray width from 100mm to 400mm
Operating humidity (RH): 30% ... 85%
Height: 1850mm
Waste conveyor: Optional
2D-code reading: Optional
Routing verification: Optional
Approx. air consumption: 100 l/min
Shuttle: maximum product width 400mm
Weight: 1800kg
Repeatability (X,Y):±0.02 mm
Repeatability (W): ±0.05º
Min. PCB size L x W: 50x50 mm Operating system: Windows 7
Max. Axis speed: 2500mm/s
ULT 200: Optional
Product teaching (CATS):
Camera-Assisted Teaching System
PCB stopper position: programmable / fixed
(option)
X-travel: 480 mm
Voltage EU (USA): 400 (208) VAC 10%
PCB pick & place: servo gripper
Gripper type identification
X-travel: 850 mm
Automatic conveyor width adjustment**:
Programmable
PCB transfer time: 1s (depending on run mode) Touch screen: Optional
Recommend routing speed: 20-40mm/sec
Others: Optional
Routing bit storage: 10 pieces
Z-travel: 50 mm
Branch circuit size: 16 A
Gripper finger change: Automatic
Multi gripper: Optional
Z-travel: 160 mm
Max. PCB board weight: 4.0kg
Max. PCB size L x W: 500 x 400 mm USB memory: Standard
Max. Acceleration: X-axis 20000mm/s2, Y-axis
12000mm/s2, Z-axis 25000mm/s2
Broken bit detection
Y-travel: 490 mm
Frequency EU (USA): 50 (60) Hz
Gripper finger width: programmable 0-100mm
Tool rack for product specific fingers: 8 positions
Y-travel: 1275 mm
PCB conveyor type: Two segments
Transfer protocol: SMEMA Ethernet card: Standard
Machine cycle time *
Dust Flow Control: Optional
Ruwac: Optional
Average power cons.: 2 kVA
W-travel: 360 degg
Top clearance: 100 mm
Transfer height: 900 ±30 mm Dual Monitors: Optional
Bottom clearance: 40 mm
2nd locating pin: Programmable
CMS (cell monitoring system): Optional
Good/bad board separation: Optional
Automatic Program Change Over: Optional
Router bit high verification: Optional
Finger validation system: Optional
Router bit diameter verification: Optional
Offline Editor: Optional
Main dimensions:
* Machine cycle time is related to PCB layout
and size
** Patented: US6222629,FI105315,Pending EP
Cencorp Corporation • Insinöörinkatu 8, FI-50100 Mikkeli, Finland • tel +358 20 7747 788, fax +358 20 7747 770 • www.cencorp.com
• [email protected] • Reg.no. 433811, VAT no. FI07496061
100
1841
1042
1960 1112
1841
1292