Specifications, Pt-d7600 – Panasonic PT-D7600E User Manual
Page 2
2
PT-D7600
DLP™-Based Projector
S P E C F I L E
Specifications
Main Unit
Power supply:
220 – 240 V AC, 50/60 Hz
Power consumption:
800 W (800 VA) (12 W during standby mode with fan stopped)
DMD™ device:
Panel size:
0.9˝ diagonal (5:4 aspect ratio)
Display method:
DMD™ (x 3, R/G/B), DLP™ system
Pixels:
1,310,720 (1,280 x 1,024) x 3, total of 3,932,160 pixels
Lens:
Optional powered zoom/focus lenses
Lamp:
300 W UHM™ lamps (x 2) (BriteOptic™ Dual Lamp System)
Screen size:
70 – 600 inches (1,778 –15,240 mm) diagonally (5:4 aspect ratio)
* 70 – 300 inches (1,778 –7,620 mm) diagonally (5:4 aspect
ratio) with the ET-D75LE5
Brightness :
6,000 lumens (dual lamp, high power mode)
Centre-to-corner uniformity ratio:
90%
Contrast:
1,000:1 (full on/full off, high contrast mode, with a high-contrast lens)
(brightness: 4,500 lumens)
600:1 (full on/full off, normal contrast mode with a standard lens
Resolution:
RGB:
1,280 x 1,024 pixels
(1,600 x 1,200 pixels compatible, compression mode)
Video:
560 TV lines
Scanning frequency:
RGB:
Horizontal: 15 –100 kHz, Vertical: 24 –120 Hz,
Dot clock: 20 –162 MHz
* Images may not be normally displayed when projecting moving pic-
tures with vertical frequency which is not between 45 Hz and 61 Hz.
YP
B
P
R
(YC
B
C
R
):
480i: f
H
15.75 kHz; f
V
60 Hz, 576i: f
H
15.63 kHz; f
V
50 Hz,
480p: f
H
31.5 kHz; f
V
60 Hz, 576p: f
H
31.25 kHz; f
V
50 Hz,
720/60p: f
H
45 kHz; f
V
60 Hz, 1035/60i: f
H
33.75 kHz; f
V
60 Hz,
1080/60i: f
H
33.75 kHz; f
V
60 Hz, 1080/50i: f
H
28.13 kHz; f
V
50 Hz,
1080/25p: f
H
28.13 kHz; f
V
25 Hz, 1080/24p: f
H
27 kHz; f
V
24 Hz,
1080/24sF: f
H
27 kHz; f
V
48 Hz, 1080/30p: f
H
33.75 kHz; f
V
30 Hz
S-Video/Video:
Horizontal: 15.75/15.63 kHz, Vertical: 50/60 Hz,
(PAL, PAL60, PAL-M, PAL-N, SECAM, NTSC, NTSC4.43)
Optical axis shift:
Horizontal and vertical (powered)
Keystone correction range:
Vertical: ±40° (±22° with the ET-D75LE5)
Installation: Ceiling/desk,
front/rear
Terminals:
RGB1 IN:
BNC x 5
R, G, B:
0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD/VD/SYNC: 1.4 Vp-p – 5.0Vp-p, 75Ω (positive/negative)
Y, P
B
, P
R
:
Y: 1.0 p-p, 75Ω, P
B,/
P
R
: 0.7 Vp-p, 75Ω
RGB2 IN/RGB1 OUT:
D-sub HD 15-pin x 1, IN/OUT selection is operated with on-screen menu.
R, G, B:
0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD/VD/SYNC: 75Ω, TTL (positive/negative polarity)
Y, P
B
, P
R
:
Y: 1.0 p-p, 75Ω, P
B,/
P
R
: 0.7 Vp-p, 75Ω
VIDEO IN:
BNC x 1, 1.0 Vp-p, 75Ω
VIDEO OUT:
BNC x 1, 1.0 Vp-p, 75Ω, active through
S-VIDEO IN:
Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75Ω
SERIAL IN:
D-sub 9-pin x 1 (RS-232C/422 compliant) for external controller
SERIAL OUT:
D-sub 9-pin x 1 (RS-232C/422 compliant) for external controller
REMOTE 1 IN:
M3 jack x 1 for wired remote control or link control
REMOTE 1 OUT:
M3 jack x 1 for wired remote control or link control
REMOTE 2 IN:
D-sub 9-pin x 1 for external control (parallel)
Optional board slot:
x 1
ET-MD95RGB
RGB/YP
B
P
R
IN:
BNC x 5
R, G, B:
0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD (H) / SYNC (H•V) • VD (V): 75Ω, TTL (positive/negative)
Y, P
B
, P
R
:
Y: 1.0 p-p, 75Ω, P
B,/
P
R
: 0.7 Vp-p, 75Ω, BETACAM compatible
ET-MD95VM2
VIDEO
BNC x 2 (IN, OUT)
VIDEO IN:
1.0 Vp-p, 75Ω or high impedance (auto selection)
VIDEO OUT:
1.0 Vp-p, 75Ω or high impedance (auto selection)
S-VIDEO IN:
BNC x 2 (Y, C)
Y, C:
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75Ω
YC
B
C
R
IN:
(BNC x 3, common with VIDEO and S-VIDEO connectors)
Y, C
B
, C
R
:
Y: 1.0 p-p, 75Ω, P
B,/
P
R
: 0.7 Vp-p, 75Ω
As of April 2004