Panasonic SCAKX12EG - Manual (Page 9)

RQTX1290
9
9
E
N
G
L
IS
H
ENGL
ISH
Sound effects
Changing the sound quality
1 Press [SOUND] to select a sound effect.
2 Press [Y, U] to select the desired setting.
BASS -4 to +4
TREBLE
SURROUND “ON SURROUND” or “OFF SURROUND”
INPUT LEVEL
(For AUX source) “NORMAL” or “HIGH”
RE-MASTER “ON RE-MASTER” or “OFF RE-MASTER”
By main unit only
1 Press [MANUAL EQ] to select “BASS” or “TREBLE”.
2 Press [2/3] or [5/6] to adjust the level.
External equipment
Using the auxiliary input
You can connect a VCR, DVD player etc. and listen to the audio
through this system.
Preparation
• Disconnect the AC mains lead.
• Switch off all equipment and read the appropriate operating
instructions.
1 Connect the external equipment.
2 Press [RADIO, EXT-IN] to select “AUX”.
3 Play the external equipment.
Note:
• Components and cables are sold separately.
• If you want to connect equipment other than those described, refer to
the audio dealer.
• Sound distortion can occur when you use an adaptor.
Remote control code
When other Panasonic equipment responds to the remote control of
this system, change the remote control code for this system.
Preparation
Press [RADIO, EXT-IN] to select “AUX”.
To set the code to “REMOTE 2”
1 Press and hold [RADIO, EXT-IN] on the main unit and [2] on
the remote control until “REMOTE 2” is shown.
2 Press and hold [OK] and [2] for a minimum of 4 seconds.
To set the code to “REMOTE 1”
1 Press and hold [RADIO, EXT-IN] on the main unit and [1] on
the remote control until “REMOTE 1” is shown.
2 Press and hold [OK] and [1] for a minimum of 4 seconds.
Sleep timer
The sleep timer switches off the system after the set time.
Press [SLEEP] to select the setting (in minutes).
To cancel, select “OFF”.
30 MIN OFF → 120 MIN → → 60 MIN → 90 MIN
To show the remaining time
Press [SLEEP].
Note:
• The sleep timer can be used together with the play timer.
• The sleep timer always comes first. Be sure not to set an overlap of
timers.
Play timer
You can set the timer to come on at a certain time to wake you up.
Switch on the system and set the clock.
Prepare the music source you want to listen to (disc, radio, USB or
AUX) and set the volume.
1 Press [CLOCK/TIMER] to select “#PLAY”.
2 Within 10 seconds, press [R, T] to set the start time.
3 Press [OK].
4 Do steps 2 and 3 again to set the end time.
To start the timer
5 Press [#, PLAY] to start the timer.
6 Press [`] to switch off the system.
The system must be switched off for the timer to operate.
Change the settings Do steps 1 through 4 and 6 again (Z above).
Change the source
or volume 1) Press [#, PLAY] to remove the timer
indicator on the display panel.
2) Change the source or volume.
3) Do steps 5 and 6 (Z above).
Check the settings Press [CLOCK/TIMER] to select “#PLAY”.
Cancel Press [#, PLAY] to remove the timer indicator
on the display panel.
Note:
• The play timer starts at a low volume and increases gradually to the
preset level.
• The timer comes on at the set time every day if the timer is on.
• If you switch off the system and switch on again while a timer is in
operation, the timer will not stop at the end time.
Preset EQ
Press [PRESET EQ] to select a setting.
HEAVY Adds punch to rock
SOFT For background music
CLEAR Clarifies higher frequencies
VOCAL Adds gloss to vocal
FLAT Cancels the sound effect
D.BASS
Press [D.BASS] to select “D.BASS”, “AUTO D.BASS” or
“OFF D.BASS”.
D.BASS Enhances bass effect
AUTO D.BASS Automatically adjusts the bass effect
according to the sound or music track
OFF D.BASS Cancels the function
SC-AKX12_EG_en.indd 9 SC-AKX12_EG_en.indd 9 2/14/2011 10:49:10 AM 2/14/2011 10:49:10 AM