Karcher K 7 Premium eco!ogic Home - Manual (Page 7)

– 2
Note: Always use Kärcher water filter (order no. 4.730-
059.0) during suction operations of the high-pressure
cleaner.
Fasten the T-Racer to the high-pressure gun using the
extension pipes.

Illustration
1 Press the extension pipe into the bayonet catch of
the T-Racer.
2 Turn it by 90° until it locks into place.
3 Tighten the union nut.
Repeat this process even for the other joints.

Adjust the twist grip "Power" in accordance with the
surface to be cleaned.
 Outdoor surfaces should be swept before the T-
Racer is used to avoid damaging the high-pressure
nozzles.
 Prior to use on sensitive surfaces (e.g. wooden sur-
faces), test the product on an imperceptible spot, in
order to promptly detect any changes in the sur-
face.
 The T-Racer is not suited for scouring or scrubbing!
 Guide the T-Racer over the surface without effort.
 Do not remain at one spot; always keep moving
during cleaning.
ṇ CAUTION
Do not run over protruding corners!

Illustration
Fasten the T-Racer directly to the high-pressure gun.
1
Press the bayonet connection of the T-Racer into
the connection of the high-pressure gun, then turn
by 90° until it locks into place.
2 Tighten the union nut.
 Adjust the twist grip "Power" in accordance with the
surface to be cleaned.
ṇ CAUTION
Always hold the T-Racer at the handle while cleaning
the walls.

Illustration
The turning handle "power" is used to change the dis-
tance of the high-pressure nozzles to the surface to be
cleaned.

Illustration
Sturdy surfaces (e.g. tiles, concrete, stone)

Set turning handle "power" to "HARD".
For the effective cleaning of hard-to-remove con-
tamination.
Sensitive surfaces (e.g. wood)

Set turning handle "power" to "SOFT".
For the gentle cleaning of sensitive surfaces.
 Illustration
For normal surface cleaning, operate the foot
switch for surface cleaning (a).
A water stream will be emitted from the two high-
pressure nozzles in the rotor arm.
 Illustration
For edge and corner cleaning, operate the foot
switch for edge cleaning (b).
A water stream will be emitted from green high-
pressure nozzle.
Note
In order to achieve the optimum cleaning result, guide
the T-Racer along the corners.
The T-Racer can be parked on level surfaces in the
parking position during breaks.

Illustration
Remove the high-pressure gun from the extension
tubes.
Push the extension tubes to the front.
You can use the extension pipes with any other Kärcher
accessory.
Use a moist cloth and clean the appliance after use.
Store the appliance in a frost free area.
The device can be suspended into the KÄRCHER or-
ganiser for storage.
Pressure washer does not build up pressure or is
pulsating.

Dismantle the high-pressure nozzles, check the
high-pressure nozzles for damage, rinse the T-
Racer with clean water then reinstall the high-pres-
sure nozzles.
 Illustration
1 Loosen the safety clamp with a screwdriver.
2 Remove the protective grid.
3 Remove the clip.
4 Pull out the high-pressure nozzle.
Rinse the high-pressure nozzle with clean water,
replace if necessary.
5 Insert the nozzle.
6 Reinsert the clip.
7 Mount the protective grid on the pin.
8 Push the safety clamp in until it locks.
Application
Cleaning floor surfaces
Tips for cleaning
Cleaning wall surfaces
Control elements
"Power" turning handle
Foot pedal for surface cleaning
Foot pedal for edge cleaning
Parking position
Tip
Care
Troubleshooting
Cleaning the high-pressure nozzle
7 EN