NoiseHush N500 - Manual

Before use, you must pair the
LED indicator chart
Note: Sniff mode means your headset has a connection with your phone but is conserving power,
and will wake up when any function is activated.
NoiseHush “N500” Bluetooth headset with your cell phone.
Pairing will create a stored connection in the headset and
your Bluetooth cell phone. Pairing has to be done only
once, when first connecting to a phone.
Charging the Headset:
Before you start, charge your “N500” unit by plugging the
USB Charger into the USB port on your computer then plug
the other end into the headset. The Red LED indicator will
light up showing that the unit is being charged. When
charging is complete the Red LED indicators will turn off.
Pairing the Headset
First turn the phone OFF and then back ON again to refresh its
memory.
Bring the mobile phone to about 30cm from NoiseHush “NH26”
headset.
3. Find the Bluetooth menu in your mobile phone. Turn Bluetooth
ON. (Check your mobile phone user guide)
4. With the NoiseHush headset OFF, Press and Hold the function
button for about 6 seconds until the LED flashes blue to red.
5. Your headset is now ready to be discovered by your Bluetooth
mobile phone.
6. Perform a Bluetooth device discovery on your mobile phone to
add a new device. It takes a few
seconds to search for and find other Blue
tooth devices around you.
7. When Bluetooth devices are found, the phone will display NoiseHush
“NH26”. Scroll to it and press OK to confirm ty want to pair with it.
8. Enter the Passkey "0000" when your phone prompts you. The phone
will now pair with the headset.
9. If your Bluetooth phone menu supports it "set as authorized" or "add
to trusted devices"
10. Again select the NoiseHush "NH26” to connect with it. OR, Press the
Function to connect with the phone.
11. If the pairing is not successful, the Headset will return to the standby
mode after a while, please repeat the pairing process to try the pairing
again.
12. Refer to your phones User Manual for any additional steps
Note: To conserve battery, NoiseHush “NH26” will automatically turn off
if it’s not paired with your phone.
Stereo Separation: 40dB
Frequency Response: 20Hz - 16Khz
• Physical
Dimensions: 110x65.5x40 mm
Weight: 191g
• Input Connection
Audio in: iPod 30PIN Connector
Blue indicator blinks 4 times
Red indicator blinks 4 times
Blue indicator blinks once every 2 seconds
Blue indicator rapidly blinks twice every 10 seconds
Red & Blue indicators alternately blink
Blue indicator rapidly blinks 2 times every 8 seconds
All Blue indicators will change to Red
Red indicator is continuously ON steady on
Red indicator turns OFF Power on
Power off
Standby mode
Sniff mode
Pairing mode
Active call
Low battery
Charging
Charging complete
Headset Functions
1. Power ON your headset:
Press and Hold the Function for about 3 seconds until the blue
indicator flashes four times. After powering on, your headset
should automatically connect to your last used phone if it is in
operating range. If no paired phone is in range or no phone has
been paired, the “N500” will enter Standby mode.
2. Power OFF your headset:
Press and Hold the Function for about 3 seconds until the red
indicator flashes twice.
3. To Answer or End a call:
Press the Function once when there is an incoming call to Answer.
Press the Function once again to end the call.
5. To Reject* a call:
Press and Hold the Function for about 2 seconds when there is an
incoming call.
6. To Redial* the last call:
Press and Hold the Volume Up Button for about 3 seconds and then
release.
7. To activate Voice Dialing*:
while connected to your phone, Press the Function once. Voice
commands must have been previously recorded into your phone
(see your phones user guide)
8. To adjust the Volume:
Click the Volume Up or Volume Down Button during a call. Adjust
to the desired level. The volume level you set to will be
remembered by the NoiseHush “N500” and used on the next call.
* To use these functions, your phone/device must support the
Bluetooth Handsfree Profile.
Contact Us
For additional help or to purchase accessories such as AC / DC,
please visit us at www.noisehush.com
Pairing the Headset:
1. First turn the phone OFF and then back ON again to refresh its
memory.
2. Bring the mobile phone to about 30cm from NoiseHush “N500”
headset.
3. Find the Bluetooth menu in your mobile phone. Turn Bluetooth
ON. (Check your mobile phone user guide)
4. With the NoiseHush headset OFF, Press and Hold the function
button for about 6 seconds until the LED flashes blue to red.
5. Your headset is now ready to be discovered by your Bluetooth
mobile phone.
6. Perform a Bluetooth device discovery on your mobile phone to
add a new device. It takes a few seconds to search for and find
other Bluetooth devices around you.
7. When Bluetooth devices are found, the phone will display
NoiseHush “N500”. Scroll to it and press OK to onfirm that you
want to pair with it.
8. Enter the Passkey "0000" when your phone prompts you. The
phone will now pair with the headset.
9. If your Bluetooth phone menu supports it "set as authorized" or
"add to trusted devices"
10. Again select the NoiseHush "N500” to connect with it. OR,
Press the Function to connect with the phone.
11. If the pairing is not successful, the Headset will return to the
standby mode after a while, please repeat the pairing process to
try the pairing again.
12. Refer to your phones User Manual for any additional steps
Note: To conserve battery, NoiseHush “N500” will automatically
turn off if it’s not paired with your phone.
noise noise
hush
innovation you can hear
®
Instruction Manual
Function Button
USB Charging port
www.noisehush.com