EnzoTech Stealth User Manual

Stealth, User’s manual, English version)

User’s Manual

(English Version)

6.WARRANTY

This guarantee does not confer rights other than those
expressly set out above and does not cover any claims for
consequential loss or damages.

7.Important Disclosures:

Enzotech is not responsible for any damages due to external causes.
Including but not limited to: improper use, problem with electrical
power, accident, neglect, alteration, repair, improper installation,
or improper testing.

(2) Intel i7 LGA 1366

1. Remove the original Clip from the motherboard.

2. Align the 1366-EZ Retention Module(J) and Backplate
(K) with the mounting holes on the motherboard and
fasten them together using the clip bolts(F).

3. Place Nylon Spacers(H) through the 4 metal rods on the
1366-EZ Retention Module(J).

4. There are four holes on the mounting bracket of the
water block to put the metal rods through.

5. Place innerspring screws(C) on the four metal rods and
fasten down until all sides are level.

Precautions

- Away from system, test product leakage before installing.
All products are tested prior to shipping; however damages
can occur during shipping and handling. Proceed with
installation and use after leakage free confirmed. Always
check your circuit for leaks prior to powering up the system.

- Never use harsh chemicals to clean your water block.
Alcohol or any other harsh solvent liquid may cause
damages to water block materials.

- Keep the product and assembly parts away from children.

CAUTION!

1.Total thread length greater than 6.5mm/0.256inch will
cause damage to the product. Enzotech warranty will not
cover this or any type of damage due to human factor.

2.CFS-ID1/2-OD3/4 connector is not used with Stealth

3.All Enzotech water blocks are only compatible with
Enzotech brand fittings. Enzotech warranty will not
cover this or any type of damage due to incorrect
installation.

6.5 mm/0.256 inch

1.Features:

1) Super high density, micro-pin design.
(0.3mm from pin to pin), provides maximum surface
exposure area for superior cooling performance.

2) Metallic Mirror coating gives elegant style and superb
finish.

3) Water block base is machined to .0003/inch run out
which optimizes surface contact and maximizes thermal
conductivity performance.

4) 100% leak tested and inspected directly from factory.

2.Specification

1).Dimension(LxWxH): 54x54x22mm
2).Base(LxWxH): 54x54x4.5mm
3).Total weight:250g

3.Components

1)Common Components
A) One (1)User

’s Manuel

B) One (1)CPU Water Block
C) Four (4)Innerspring Screws
D) Two (2)1/2” HI-Flow Hose Barbs with gaskets
E) Two (2)Tube Clamps
G) One (1)

Arctic Silver

Céramique™ Thermal Grease (OEM)

2)Components for Intel (Socket 775)

I) One (1)Backplate for Socket 775

3)Components for i7 LGA 1366

F) Four (4)Clip Bolts
H) Four (4)Nylon Spacers
J) One (1)1366-EZ Retention Module
K) One (1)Backplate for LGA 1366

5.Tubes and Fittings Installations

1. Fit tubes over water block

’s hose barb fittings with

gaskets.Secure tubes using the supplied tube clamps(E).
2. Tighten the hose clamp using a screw driver. Make
sure the clamps are securely tightened. Do not over
tighten it! Always check for leakage before system
power up.

4.Installation

(1)Intel Pentium 4-775

1. Align Backplate (I) for “Socket 775”on the back side
of the motherboard.

2. Place CPU Water block with the mounting bracket (B)
on center of the CPU.

3.There are four holes on the mounting bracket of the
water block to put the metal rods through.

4. Place innerspring screws on the four metal rods and
fasten down until all sides are level.

Stealth

OUTLET

INLET

User’s Manual

(English Version)

Stealth