beautypg.com

Assembly instructions 4, Iris ja ck osd ex tra video out power video dc set – Clinton Electronics CE-H13 User Manual

Page 3

background image

CLINTON Electronics

6701 Clinton Road

Loves Park, IL 61111

1.800.447.3306 Sales

1.800.549.6393 Support

1.800.633.8712 Fax

www.clintonelectronics.com

Assembly Instructions
4.

Prepare to route wires

Unscrew the cable nut to reveal a plastic nipple inserted in the
nut. Remove this piece and lightly screw on the cable nut to pre-
pare to feed the cables through the hole.

5.

Feed wires through hole

Feed the wires through the cable nuts on the bottom of the
camera, and pull as much slack as needed into the interior of the
camera housing. Tighten the cable nuts, then place the housing
on the arm to prepare for the next step.

6.

Attach Housing to Arm

Attach the housing to the arm of the mount by tightening the
four allen screws located on the underside of the arm.

7.

Adjust Angle

You can adjust the angle of the arm by loosening the single allen
screw located on the underside of the mount’s arm. Gently pull
upward on the base of the housing, and rotate. *NOTE: Loosen
screw just enough to move the housing into position. Loosen-
ing all the way will separate the arm from the housing.
Adjust
the arm slowly to protect the housing lid from opening, or the
internal camera from harsh movements.

Cord route option 1:

back of arm

Cord route option 2:

bottom of arm

IRIS JA

CK

OSD EX

TRA

VIDEO OUT

POWER

VIDEO

DC

SET

BNC Input

24V AC Jumper

to Camera

24V AC Input to

Fan/Heater Board

Gently pull upward from

base of housing & rotate

Secure housing lid & internal

camera when adjusting

Plastic Adaptor

Plate Optional

Loosen screw just

enough to adjust

Cord route option 1:

back of arm

Cord route option 2:

bottom of arm

IRIS JA

CK

OSD EX

TRA

VIDEO OUT

POWER

VIDEO

DC

SET

BNC Input

24V AC Jumper

to Camera

24V AC Input to

Fan/Heater Board

Gently pull upward from

base of housing & rotate

Secure housing lid & internal

camera when adjusting

Plastic Adaptor

Plate Optional

Loosen screw just

enough to adjust

8.

Complete setup

Make any final electrical connections to the heater/fan board
and camera. Typical 24V/1A AC connection will run to the heater
board first, then a jumper from the board to the camera.

Test and verify focus, zoom, and other parameters before closing
the case. Once complete, close the housing by tightening the two
allen screws that were loosened in Step 2.

Cord route option 1:

back of arm

Cord route option 2:

bottom of arm

IRIS JA

CK

OSD EX

TRA

VIDEO OUT

POWER

VIDEO

DC

SET

BNC Input

24V AC Jumper

to Camera

24V AC Input to

Fan/Heater Board

Gently pull upward from

base of housing & rotate

Secure housing lid & internal

camera when adjusting

Plastic Adaptor

Plate Optional

Loosen screw just

enough to adjust

Cord route option 1:

back of arm

Cord route option 2:

bottom of arm

IRIS JA

CK

OSD EX

TRA

VIDEO OUT

POWER

VIDEO

DC

SET

BNC Input

24V AC Jumper

to Camera

24V AC Input to

Fan/Heater Board

Gently pull upward from

base of housing & rotate

Secure housing lid & internal

camera when adjusting

Plastic Adaptor

Plate Optional

Loosen screw just

enough to adjust

Cord route option 1:

back of arm

Cord route option 2:

bottom of arm

IRIS JA

CK

OSD EX

TRA

VIDEO OUT

POWER

VIDEO

DC

SET

BNC Input

24V AC Jumper

to Camera

24V AC Input to

Fan/Heater Board

Gently pull upward from

base of housing & rotate

Secure housing lid & internal

camera when adjusting

Plastic Adaptor

Plate Optional

Loosen screw just

enough to adjust

Cord route option 1:

back of arm

Cord route option 2:

bottom of arm

IRIS JA

CK

OSD EX

TRA

VIDEO OUT

POWER

VIDEO

DC

SET

BNC Input

24V AC Jumper

to Camera

24V AC Input to

Fan/Heater Board

Gently pull upward from

base of housing & rotate

Secure housing lid & internal

camera when adjusting

Plastic Adaptor

Plate Optional

Loosen screw just

enough to adjust