beautypg.com

Asus Motherboard A8N-SLI User Manual

Page 53

background image

A S U S A 8 N - S L I D e l u x e

A S U S A 8 N - S L I D e l u x e

A S U S A 8 N - S L I D e l u x e

A S U S A 8 N - S L I D e l u x e

A S U S A 8 N - S L I D e l u x e

2 - 2 7

2 - 2 7

2 - 2 7

2 - 2 7

2 - 2 7

1 1 .

1 1 .

1 1 .

1 1 .

1 1 . Chassis intrusion connector (4-1 pin CHASSIS)

C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )

C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )

C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )

C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch
cable to this connector. The chassis intrusion sensor or switch sends a
high-level signal to this connector when a chassis component is
removed or replaced. The signal is then generated as a chassis
intrusion event.

By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to
use the chassis intrusion detection feature. See related BIOS item in
page 4-42.

Never connect a U S B c a b l e

U S B c a b l e

U S B c a b l e

U S B c a b l e

U S B c a b l e to the IEEE 1394 connectors. Doing so will

damage the motherboard!

1 2 .

1 2 .

1 2 .

1 2 .

1 2 . IEEE 1394 connector (10-1 pin IE1394_2)

I E E E 1 3 9 4 c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 2 )

I E E E 1 3 9 4 c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 2 )

I E E E 1 3 9 4 c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 2 )

I E E E 1 3 9 4 c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 2 )
This connector is for the IEEE 1394a module. Connect the IEEE 1394
module cable to this connector, then install the module to a slot
opening at the back of the system chassis.

A8N-SLI DELUXE

®

A8N-SLI DELUXE Chassis alarm lead

CHASSIS

+5VSB_MB

Chassis Signal

GND

(Default)

A8N-SLI DELUXE

®

A8N-SLI DELUXE IEEE 1394 connector

IE_1394_2

1

GND

+12V

TPB1-

GND

TP

A1-

+12V

TPB1+

GND

TP

A1+

This manual is related to the following products: