LG DLG4902W - Manual (Page 26)

26 INSTALLATION INSTRUCTIONS
Special requirements for
manufactured or mobile homes
Any installation in a manufactured or mobile home must comply
with the Manufactured Home Construction and Safety Standards
5JUMF$'3
1BSUPS4UBOEBSE$"/$4";.)BOE
local codes and ordinances. If you are uncertain whether your
proposed installation will comply with these standards, please
contact a service and installation professional for assistance.
t"HBTESZFSNVTUCFQFSNBOFOUMZBUUBDIFEUPUIFGMPPS
t5IFFMFDUSJDBMDPOOFDUJPOGPSBOFMFDUSJDESZFSNVTUCFBXJSF
connection. More detailed information concerning the electrical
connection is provided in the section Connecting Electric Dryers.
t5PSFEVDFUIFSJTLPGDPNCVTUJPOBOEGJSF
UIFESZFSNVTUCF
vented to the outside.
t%0/05WFOUUIFESZFSVOEFSBNBOVGBDUVSFEIPNFPSNPCJMF
home.
t&MFDUSJDESZFSTNBZCFWFOUFEUPUIFPVUTJEFVTJOHUIFCBDL
MFGU
right, or bottom panel.
t(BTESZFSTNBZCFWFOUFEUPUIFPVUTJEFVTJOHUIFCBDL
MFGU
or bottom panel. Gas dryers may not be vented to the outside
using the right side panel because of the burner housing.
t5IFESZFSFYIBVTUEVDUNVTUCFBGGJYFETFDVSFMZUPUIF
manufactured or mobile home structure, and the exhaust duct
must be made of a material that will resist fire and combustion.
It is recommended that you use a rigid or flexible metal duct.
t%0/05DPOOFDUUIFESZFSFYIBVTUEVDUUPBOZPUIFSEVDU
WFOU
chimney, or other exhaust duct.
t.BLFTVSFUIFESZFSIBTBEFRVBUFBDDFTTUPPVUTJEFGSFTIBJSUP
ensure proper operation. The opening for outside fresh air must
CFBUMFBTUJO
DN ).
t*UJTJNQPSUBOUUIBUUIFDMFBSBODFPGUIFEVDUGSPNBOZ
DPNCVTUJCMFDPOTUSVDUJPOCFBUMFBTUJODIFT DN
BOEXIFO
venting the dryer to the outdoors, the dryer can be installed with
BDMFBSBODFPGJODI DNBUUIFTJEFTBOECBDLPGUIFESZFS
t1MFBTFCFBXBSFUIBUWFOUJOHNBUFSJBMTBSFOPUTVQQMJFEXJUI
the dryer. You should obtain the venting materials necessary for
proper installation.
Final installation check
Once you have completed the installation of the dryer and it is
in its final location, confirm proper operation with the following
tests and Installation Test (Duct Check) on the following page.
Testing dryer heating
("4.0%&-4
Close the dryer door, press the ON/OFF button to turn the dryer
on, and start the dryer on a heat setting. When the dryer starts,
the igniter should ignite the main burner.
&-&$53*$.0%&-4
Close the dryer door, press the ON/OFF switch to turn the dryer
on, and start the dryer on a heat setting. The exhaust air should
be warm after the dryer has been operating for 3 minutes.
Checking airflow
Effective dryer operation requires proper airflow.
The adequacy of the airflow can be measured by evaluating
the static pressure. Static pressure in the exhaust duct can
be measured with a manometer, placed on the exhaust duct
BQQSPYJNBUFMZGU DNGSPNUIFESZFS
4UBUJDQSFTTVSFJOUIFFYIBVTUEVDUTIPVMEOPUFYDFFEJODIFT
DN5IFESZFSTIPVMECFDIFDLFEXIJMFUIFESZFSJTSVOOJOH
with no load.
Checking levelness
Once the dryer is in its final location, recheck the dryer to be sure
it is level. Make sure it is level front to back and side to side, and
UIBUBMMMFWFMJOHGFFUBSFGJSNMZPOUIFGMPPS
NOTE
If all air is not purged from the gas line, the gas igniter may turn
off before the main burner ignites. If this happens, the igniter
will reattempt gas ignition after approximately two minutes.