Electrolux EDBS3350 - Manual (Page 29)

EN
GETTING STARTED
1. Before first use. Remove all adhesive remains and
gently rub with a dampened cloth. Position the steam
generator iron horizontally on the ironing-board or
on a heat resistant, secure surface at the same height
as an ironing-board. Unwind and straighten the
power cord and the steam cord. When turned on for
the first time, temporary vapours/odours may occur.
2. Remove the water tank by gripping the slot on
the underside and pulling it gently away from the
base unit. (A)Detach the anti-calc cartridge and then
immerse it in water for more than one minute. (B)
Insert the anti-calc catridge back. Fill the water tank
using cold water. It is recommended to use destilled
water or a mix of 50% destilled, 50% tap water. Empty
the water tank to rinse out any foreign particles
which may remain from the manufacturing process.
3. Always refill the water tank to MAX level using cold
water (A). insert the water tank into the base unit (B).
It is recommended to use destilled water or a mix of
50% destilled, 50% tap water. Ensure that the water
tank latches securely into place.
4. Connect the steam generator iron to the mains
supply. Press the power button (A). Turn the
temperature selector clockwise to maximum setting
(B). The temperature indicator light on the iron will
illuminate. Then, select a steam level on the control
panel, from low - medium - high steam.
5. When the temperature indicator light turns on, the
steam station is pre-heating. When the light turns off, it
is ready to be used. Press and hold the steam button for
about one minute to get steam. Then hold one more
minute in order to clean the steam generating system.
6. Iron an old towel, to ensure that any residues inside
the iron are not transferred to the laundry.
If necessary, wipe the sole plate with a slightly damp
cloth.
OPERATING INSTRUCTIONS
7. Connect the steam generator iron to the mains
supply. Press the power button. When the power
switch is pressed, the power indicator will illuminate.
Wait for one to two minutes, until the steam lamp
lluminates. Select the steam level between Low
- Medium and High. See Ironing chart for ironing
recommendation.
8. if the lower water level indicator is illuminated (A)
(followed with two beep sounds), refill the water tank.
After refilling the water tank, press and hold the refil
reset button (B) for about 6 seconds. The refill reset
button will be extinguished. Steam can now be used
again.
9. To activate the steam, press the steam button. When
releasing the button, use up the steam before putting
it back on the iron rest of the steam station.
10. To turn off the iron by pressing the power button
for a while, until a beep will sound. If the iron is left
unattended on the iron rest, it turns automatically off
after 10 minutes.
11. Always cool the iron fully on the iron rest before
stowing away. Once the iron is cool, empty the water
tank. Store the steam generator iron
12. Always store the cord winded safely by the side of
the iron. NEVER wind the power cord around the iron
CLEANING
(DO NOT USE ANY DETERGENT)
13. Always store iron on its heel rest.
To clean exterior surfaces, use a damp soft cloth and
wipe dry.
Caution: Do not use any chemical solvents, as these
will damage the surface.
14. Replacing the de-calc box: If the descaling indicator
is illuminated detach the water tank. Remove the
de-calc box by pulling it upwards. Immerse a new
de-calc box in water for more than one minute, then
place it inside the water tank. Ensure the new de-
calc box is correctly positioned, if not, the descaling
indicator will keep flashing.
For the best performance we recommend cartridge
from our range, reference number EDC06.
15. When finished using the appliance, turn the
temperature dial to the OFF (“0“) position. Store the
iron on the iron rest.
Note: Do not store the iron with water in the tank.
29
BG
EE
NO
FR
RU
CS
LT
EN
PL
HR
SK
SV
DA
LV
ES
PT
HU
SL
TR
DE
NL
FI
RO
IT
SR
UK