Source Green Heat SGH‐1000 - Manual (Page 3)

Warranty Limitations
This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or repairs
(unless authorized verbally, or in writing, by an Authorized SGH Representative) alteration by non SGH
authorized personnel, inappropriate installations, or any case beyond the control of SGH. Examples of
warranty invalidation may also include, but are not limited to:
• Use of lacquer or paints in (and around) the
heaters
• Use on Extension Cords/Timers/Surge
Protectors/GFCI
• Outdoor applications
• Normal wear/tear/weathering
• Pet/purchaser accidents
• Purchases from dealers unauthorized by
SGH (Authorization in writing)
• Electrical requirement deficiencies (15-20
amp dedicated outlet required)
• Heater placed on non-approved surfaces
Disclaimers
SGH shall not be liable for any loss due to use (or misuse) of the heater or other SGH products or other
incidental or consequential costs, expense or damages without irrefutable foundations. Under no
circumstances shall SGH or any of its representatives be held liable for injury to any person or damage to
any property, however arising. Any implied warranty shall have duration equal of the applicable warranty
stated above. Specifications are subject to change without notice or obligation.
Legal Remedies
This limited warranty gives the original purchaser specific legal rights. Other rights may vary from
state to state.
10
ƒ Use heater only as described in this manual. Any other use is not recommended by the
manufacturer as it may lead to fire, electric shock, and/or series physical injury or death.
Heater Specifications
SGH Heater Model# SGH-1000
Carton Size: 19.4 in x 17.1 in x 18.6 in Thermostat: Electronic Analog
Heater Size: 15.8 in x 14.8 in x 16.2 in
Fan System: Cross Flow Fan
Net Weight: 32 lbs Fan Noise Level: 46 db
Gross Weight: 36 lbs BTU: Over 5100
Cabinet: Wood – Oak Delayed Start Function
Power Cord: 5.8 ft / 16 gauge Remote Control
Heat Chamber with Diathermanous Copper Plate “HI” Function: 1500 watts
Heating Elements: 4 Infrared Quartz Bulbs w/ Nickel-Chrome Filament “LOW” Function: 750 watts
Power Requirement: 120V 15 amp Electrostatic Washable Filter
Heating Elements Life Expectancy Potential: Rated 20,000 hrs Warranty: Limited 3-Year Parts Only
Heat Type: Quartz Infrared Heat
How It Works
The SGH Infrared Heater works with your in-home furnace to provide supplement heat. In short, room
temperature air circulates from the rear of the SGH Infrared Heater, passes through a highly efficient filter,
enters a chamber that houses the Infrared Quartz Bulbs, and exits as heated air from the Diathermanous
Copper Plate constructed on the front of the unit. The SGH Infrared Heater ideally heats a room of up to
750 square feet, but can be used to heat up a single room size up to 1000 square feet, depending on the
ambient temperature. And it does all this with a noise level below 46db. The SGH Infrared Heater is not
for use as the primary/sole heating system.
Components and Functions
A. The SGH Infrared Heater is constructed with Infrared Quartz Bulbs. Each Infrared Quartz Bulb is
rated at 375W. These bulbs produce infrared rays that warm the air which passes through the
inner chamber. The Infrared Quartz Bulbs are constructed with a stainless steel thermal
conducting housing. The incorporated twisted style increases the efficiency of the unit.
B. An AC Cross Flow Fan pushes air over these Infrared Quartz Bulbs. Cross Flow Fans create a
wide flow of air using a cylindrical-shaped impeller. Air is drawn inside the SGH Infrared Heater,
flows along the circumference of the chamber and over the Infrared Quartz Bulbs, and is blown
out laterally creating a uniform flow of warm air.
C. The SGH Infrared Heater has a Delay Start Function which controls the AC Cross Flow Fan. The
purpose of the Delay Start Function is to allow the Infrared Quartz Bulbs to heat up before the fan
begins to circulate the air flow. In addition, the AC Cross Flow Fan will continue to circulate the
airflow after the power is turned off to circulate the warm air from the SGH Infrared Heater cooling
the unit down.
D. The air flow exits through the front of the SGH Infrared Heater. It travels from the Diathermanous
Copper Plate. The Diathermanous Copper Plate is constructed from red copper making it
advantageous for efficient thermal conductivity. It is a resourceful material in reflecting the
infrared rays.
E. The LED Digital Display is a convenient, stylish, and modern way to display the set temperature
and time. This attractive addition compliments the SGH Infrared Heater, in that, it simplifies and
makes controlling the unit easy. Operating the heater is logical and can be done on the unit itself
or by remote.
3