Rapid-Air SMART MINI-SERVO GAG FEED - Manual (Page 9)

ProGramminG ProCedUre
(ContinUed)
corresponds to Output 1 in the electri-
cal wiring diagram. Entering 1 will
turn an output on at the end of each
feed. Entering 0 will keep the output
turned off. If the speed, accel and
decel are within acceptable limits,
the main screen will reappear. If the
values are outside acceptable limits,
the following screen will appear.
vALUES OUT OF RANGE
MAX SPEED EXCEEDED
FEED IS LONG OR % IS
ShORT F6 TO RETURN
Pushing F4 will take an operator back
to the feed advisor screen. After en-
tering valid data, the “MAIN MENU”
will be displayed.
NOTE: If a job number is not selected
and the selected task requires a job
with a feed length and speed to be
active, the following screen will ap-
pear. After a valid job is entered the
program will return to the original task.
A vALID JOB # MUST
BE ACTIvE TO GO ON
GO TO JOB ENTER SCRN
JOB SCRN F6=EXIT
SECTION 2 F2 - MANUAL MODE
Pressing F2, manual mode while on
the “MAIN MENU”, will cause the
following the screen.
EXIT
MANUAL MODE
INCh FEED SGL
MODE LENGTh
F1, inch mode, produces the following:
EXIT
CONTINUOUS JOG:
USE X kEYS TO
JOG + OR -
This allows an operator to jog each
axis in either direction. The X-axis
keys move the feed axis.
F3, feed sgl length, produces the
following:
EXIT
JOB 00 LENGTh = 00.000
FEED 1
LENGTh
F6, exit, in both screens moves the
display back to “MANUAL MODE”.
SECTION 3 F3 - AUTOMATIC MODE
Pressing F3, automatic mode while
on the “MAIN MENU”, will cause the
following the screen.
START AUTOMATIC FROM
F1 = SEQUENCE NUMBER 1
F2 = PREvIOUS SEQUENCE
Pushing F1 will start the job from
sequence number 1. Pushing F2
will resume the job at the sequence
at which it was either stopped or
interrupted. The machine will
remember the previous sequence
even after the power has been reset
as long as the active job number
hasn’t been changed.
EXIT
AUTOMATIC MENU:
BATCh AUTO
MODE MODE
F1, batch mode, controls batches from
the “BATCH START” screen.
EXIT
BATCh SIZE = 000000
BATCh COUNT = 000000
ST_CYC SET_CNT CONT
The F1 key, ST_CYC (start cycle), will
begin the feed/cut cycle. The “BATCH
MENU” screen appears as follows.
CURRENT TOTAL = 000000
BATCh SIZE = 000000
JOB # =00 % SPEED = 000
LGhT = 00.000 F6 = EXIT
The F2 key, SET_CNT (set count), will
allow the operator to set the batch
size or change the batch size. The
“BATCH SET” screen is:
INPUT A BATCh SIZE
BATCh SIZE = 000000
START
CYCLE F6 = EXIT
The F3 key, CONT (continue), will re-
start a batch stopped before reaching
the full batch size by exiting with the
F6 key. The “BATCH MENU” screen is:
CURRENT TOTAL = 000000
BATCh SIZE = 000000
JOB#=00 %SPEED = 000
FEED LENGTh = 00.000 F6 = EXIT
NOTE: If the batch size is set to
000000, the “BATCH SET” screen will
appear. The “BATCH SET” screen will
allow an operator to set the batch
count. The “BATCH SET” screen can
also be found under ramp/count se-
lection on the “MAIN MENU” screen.
The “BATCH SET” screen is shown
above under F2. After the batch size
is entered and F1 (start cycle) is
pressed, the program will return to
“BATCH SET” screen.
When the batch total equals the
batch size, the feed will stop and will
display this screen.
EXIT
BATCh CYCLE COMPLETE
BATCh COUNT = 000000
NEw CYCLE
F6, exit, will return to the “MAIN
MENU” screen. F1, start new cycle,
will reset the batch count total to 000000
and will start feeding another batch.