ION Audio Rock Block - Manual

1 2 3
4 5
6 7
Quickstart Guide
Rock Block
Controls: (1) Power; (2) Volume Down/Up Controls; (3) Next Track;
(4) Unpair Button (Disconnects current Bluetooth connection); (5)
Battery Charging LED; (6) micro-USB Charging Port; (7) Aux Input.
Getting Started: (1) Power on Rock Block. (2) Open Bluetooth
settings on your music device (smartphone, tablet, etc.). (3) Connect
to Rock Block. (4) Play music and adjust Rock Block’s volume
buttons.
For the complete multilingual User Guide, visit ionaudio.com/rock-
block.
For the Safety and Warranty manual, visit ionaudio.com/warranty.
or
ionaudio.com/support
For technical support.
Para soporte técnico.
Pour obtenir de l’assistance technique.
Per assistenza tecnica.
Für technischen Support.
Voor technische ondersteuning.
ionaudio.com/warranty
For complete warranty information.
Para información completa sobre la garantía.
Pour obtenir toutes les informations relatives à la garantie.
Per informazioni complete in merito alla garanzia.
Für komplette Garantieinformationen.
Voor volledige informatie over de garantie.
Manual Draft v1.5
Box Contents: Rock Block, USB Charging Cable, 3.5 mm (1/8”)
Stereo Aux Cable, Quickstart Guide.
Charging Rock Block: Use the included micro-USB cable to
connect Rock Block to (A) a USB power adapter connected to a
power outlet or (B) your computer (powered on) for 3 hours.
Notice Concerning FCC Regulations: You are cautioned that changes or modifications not
expressly approved by the part responsible for compliance could void the user's authority to
operate the equipment. This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: (a) reorient or relocate the receiving
antenna; (b) move this unit; (c) increase the separation between the equipment and receiver; (d)
connect the equipment into an outlet on a circuit different from that to which the receiver is
connected; (e) be sure that all cables are properly shielded, using a choke or ferrite where
appropriate; (f) consult the dealer or an experienced radio/television technician for help.
ESD / EFT Warning: This unit may contain a microcomputer for signal
processing and control functions. In very rare situations, severe interference,
noise from an external source, or static electricity may cause it to lock up. In the
unlikely event that this should happen, turn off the unit, wait at least five seconds,
and then turn it back on again.
In an environment with radio frequency interference, the unit may malfunction and resume normal
operation after removal of the interference. For best audio quality, avoid using this device in a
high RF-radiated environment. This unit does not exceed the Class B limits for radio noise
emission from digital apparatus set out in the radio interference regulations of the Canadian
Department of Communications.
The Bluetooth word mark and logo are owned by the Bluetooth SIG, Inc. and any use of such
marks by ION Audio is under license.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
The Bluetooth word mark and logo are owned by the
Bluetooth SIG, Inc. and any use of such marks by ION
Audio is under license.
Rock Block LED activity:
The Battery Charging LED (5)
will be lit while the unit is
charging and the LED will turn
off when charging has
completed.
Solid Red LED = No Bluetooth connection.
Solid Blue LED = Bluetooth connected.
Blinking Red LED = Battery is low and needs to be recharged (no
Bluetooth connection).
Blinking Blue/Purple LED = Battery is low and needs to be
recharged (Bluetooth connected).