Bosch Scopa elettrica BHS41825 Pro Animal hepa 1800 W - Manual (Page 80)

79
Replacement parts and accessories
A Replacement filter pack BHZ4AF1 / Type S
Contains:
8 self-sealing dust bags
1 micro-hygiene filter
B Adapter for special nozzles BBZ4AD1
Required for BBZ102TBB and BBZ103WD.
C TURBO-UNIVERSAL ® brush
for floors BBZ102TBB
All in one brushing and vacuuming of short-pile pile
rugs and carpets and all hard floor coverings. Especially
suitable for picking up pet hair.
The brush roller is driven by the air flow through the
vacuum cleaner.
No separate electrical connection is needed.
Setting up
Version A
Ⅲ Engage the handle in the suction hose/telescopic tube.
To remove the handle, press the notch button and pull
the handle out of the suction hose/telescopic tube.
Ⅲ Turn the locking ring on the vacuum cleaner to position
and insert the suction hose/telescopic tube in the
opening.
Ⅲ Lock the suction hose/telescopic tube in place by turning
the ring to position .
To remove the suction hose / telescopic tube, move the
ring back to position
and pull out the suction
hose/telescopic tube.
Ⅲ Connect the floor tool to the vacuum cleaner.
Version B
Ⅲ Turn the locking ring on the vacuum cleaner to position
and insert the handle in the opening.
Lock the handle in place by turning the ring to
position .
To remove the handle, move the ring back to position
and pull out the handle.
Ⅲ Fit the telescopic tube to the vacuum cleaner.
Ⅲ Connect the floor tool to the telescopic tube.
ELECTROMATIC ® brush
Your vacuum cleaner is equipped with an ELECTROMATIC ®
brush. For notes on use and maintenance, please refer to
the accompanying instruction manual.
Figure
Press the adjusting sleeve in the direction of the arrow
and adjust the telescopic tube to the length required.
Figure
Release the lower power cord hook by turning it and
remove the cord from the upper power cord hook.
Connect the plug to the mains socket.
2
1
Figure
Turn the vacuum cleaner on/off at the switch.
Figure
Adjust the suction setting by turning the rotary control.
Vacuuming
Figure
Adjusting the floor tool:
Ⅲ Rugs and
carpets =>
Ⅲ Hard surfaces
=>
Caution!
Floor tools are subject to a certain amount of wear,
depending on the type of hard floors you have
(e.g. rough, rustic tiles). Therefore, you must check
the underside of the floor tool at regular intervals.
Worn undersides of floor tools may have sharp edges
that can damage sensitive hard floors, such as parquet
or linoleum. The manufacturer does not accept any
responsibility for damage caused by worn floor tools.
Vacuum using flexible tube
Figure
a) Switch off the vacuum cleaner.
b) Press the rotary knob in the direction of the arrow to
release it and set it to the flexible tube position.
c) Pull the hose adapter out of the holder in the direction of
the arrow.
Figure
Fit an accessory to either the flexible tube or the suction
hose/telescopic tube.
a) Crevice nozzle
For cleaning crevices and corners.
b) Upholstery nozzle
For cleaning upholstered furniture, curtains, etc.
Figure
Hard-floor brush
For cleaning hard floor coverings
(tiles, parquet flooring, etc.)
Figure
a) Switch off the vacuum cleaner.
b) Insert the hose adapter back into the holder.
c) Press the rotary knob to release it and turn it back to the
floor tool position.
When the work is done
Figure
Unplug the vacuum cleaner.
Wind the cord around the power cord hooks at the rear
of the vacuum cleaner.
10
9
8*
7*
6
5
4
3
9000 794 642 A (Innenteil) 20.06.2012 15:46 Uhr Seite 79