Poulan Pro PR625Y22RKP LAWN MOWER - Manual (Page 8)

8
Remote
throttle
control
FAST
SLOW
CHOKE
(START)
OPERATION
The operation of any lawn mower can result in foreign objects thrown into
the eyes, which can result in severe eye damage. Always wear safety
glasses or eye shields while operating your lawn mower or performing any
ad just ments or repairs. We recommend standard safety glasses or a wide
vision safety mask worn over spectacles.
• Reinstall wheel components in the same
order as they were before removal.
Tighten securely.
• Make sure all wheels are at same height.
MODELS WITH “QUICK ADJUST”
WHEEL HEIGHT ADJUSTERS
NOTE: For shipping purposes, the rear
wheels on your lawn mower may not be
adjusted to the same position as the front
wheels. Before operating mower adjust all
wheels to the same cutting height.
• Raise wheels for low cut and lower
wheels for high cut.
• Adjust cutting height to suit your require-
ments. Me di um position is best for most
lawns.
• To change cutting height, squeeze adjuster
lever to ward wheel. Move wheel up or
down to suit your re quire ments. Be sure
all wheels are in the same setting.
NOTE: Adjuster is properly positioned when
plate tab inserts into hole in lever. Also, 9-
position adjusters (if so equipped) allow lever
to be positioned between the plate tabs.
Bolt
Flat washer
Wheel
3/8-16
Locknut Spacer
LEVER BACKWARD
TO LOWER MOWER
LEVER FORWARD TO RAISE MOWER
Plate tab
Lever
HOW TO USE YOUR LAWN MOWER
ENGINE SPEED CONTROL
MODELS WITH REMOTE THROTTLE
Engine speed is con trolled by the throttle
control located on the upper handle.
• Move lever forward to FAST engine
speed for start ing and better bagging.
• Move lever backward for SLOW engine
speed.
• Some models have engines equipped
with a choke feature. Move the lever all
the way forward to the CHOKE position
when starting a cold engine.
MODELS WITH FIXED SPEED ENGINES
Engine speed was set at the factory for
optimum per form ance. Engine speed is
not adjustable.
TO ADJUST CUTTING HEIGHT
Adjust cutting height to suit your re quire -
ments. Me di um position is best for most
lawns. Raise wheels for low cut and lower
wheels for high cut.
MODELS WITH MANUAL ADJUST
BOLT-ON WHEELS
• Remove wheel, bolt, and hardware and
reassemble in desired adjustment hole.
13
FOR MULCHING MOWERS ONLY
- MULCHING MOWING TIPS
IMPORTANT: For best performance, keep
mower housing free of built-up grass and
trash. See "CLEANING" in the Mainte-
nance section of this manual.
• The special mulching blade will recut the
grass clip pings many times and reduce
them in size so that as they fall onto the
lawn they will disperse into the grass
and not be noticed. Also, the mulched
grass will bio de grade quickly to provide
nu tri ents for the lawn. Always mulch with
your highest engine (blade) speed as
this will provide the best recutting action
of the blades.
• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
in ter feres with the mulch ing action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried, yet the newly cut area will not be
exposed to direct sunlight.
• For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third of the
grass blades. If the lawn is overgrown it
will be necessary to raise the height of
cut to reduce pushing effort and to keep
from over load ing the engine and leaving
clumps of mulched grass. For ex tremely
heavy grass, reduce your width of cut by
overlapping previously cut path and mow
slowly.
MOWING TIPS
CAUTION: Do not use de-thatcher
blade attachments on your mower. Such
attachments are hazardous, will damage
your mower and could void your warranty.
• For most cutting conditions and bet ter
bagging per form ance, the engine speed
should be set in the FAST po si tion.
• Under certain conditions, such as when
mowing very tall grass, raise the mower
height on the fi rst cut to reduce pushing
effort, to avoid over heat ing the engine,
and to avoid leaving clumps of grass
clippings. Make the second cut to the
desired height.
• For extremely heavy cutting, reduce the
width of cut.
• For side discharge lawn mowers, cut in
a coun ter clock wise di rec tion, start ing at
the outside of the area to be cut, in order
to spread grass clip pings more evenly
and to put less load on the engine. To
keep clip pings off of walkways, fl ower
beds, etc., make the fi rst cuts in a clock-
wise direction.
• When using a rear discharge lawn
mower in moist, heavy grass, clumps
of cut grass may not enter the grass
catcher. Reduce ground speed (push ing
speed) and/or run the lawn mower over
the area a second time.
• If a trail of grass clipping is left on the
right side of a rear discharge lawn mow-
er, mow in a clockwise direction with a
small overlap to collect the clippings on
the next pass.
• Pores in cloth grass catchers can be-
come fi lled with dirt and dust with use
and the catcher will collect less grass.
To prevent this, regularly hose catcher
off with water and let dry before use.
• Certain types of grass and grass
con di tions may re quire that an area be
mulched a second time to com pletely
hide the clip pings. When doing a sec ond
cut, mow across (per pen dic u lar) to the
fi rst cut path.
• Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn.
MAX 1/3