intimus 319 - Manual (Page 7)

MATERIAL JAM IN THE MACHINE:
(Auto reverse function)
If a jam is caused by too much material being fed in
the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display (6) comes
on.
Proceed as follows:
Paper jam in paper feed slot (12)
- Remove the paper that has been fed back.
- The cutters now run forwards automatically and
shred the remaining paper in the cutters. During
the forward run the forward button (3) LED
display comes on. The control display
(6)
goes out.
- Continue shredding with less paper.
Material jam in CD/DVD feed slot (13)
- Remove the returned material.
Remove the material carefully
because there is the risk of being
injured by the sharp cut surfaces.
- The remaining material to be cut is now
automatically fed to the cutters again and
shredded. During the forward run the forward
button (3) LED display comes on. The control
display (6) goes out.
- If the material to be cut has gone through continue
shredding with the right amount of material.
- If necessary, switch the cutters manually
alternately from forward to reverse until the
material has gone through completely and been
shredded.
SIMULTANEOUS MATERIAL FEED:
Should material be fed into the two feed slots at the
same time the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display (6) comes
on.
- Take the material out of one of the slots.
- Press the forward button (3) briefl y. The material
in the other slot is fed to the cutters and shredded.
The control display (6) goes out.
LIGHT BARRIER OCCUPIED
WHEN THE WASTE BIN MOVES OUT:
If there is still material in one of the two feed
slots when the waste bin is moved out, the motor
switches off and the cutters stop. The control
display (6) comes on.
Push the waste bin in again and acknowledge
the status by briefl y pressing the forward button
(3). The existing material is fed to the cutters and
shredded.
LIGHT BARRIER COVERED
WHEN MACHINE TURNED ON:
Should there still be material in one of the two feed
slots when the machine is switched on the control
display (6) comes on.
Remove the material and acknowledge the status
by pressing the forward button (3) briefl y.
MOTOR PROTECTION:
Should the motor be overloaded it switches off. The
control display (9) comes on.
The machine can be started again after a cooling
down period of about 25 – 40 minutes (depending
on the model and the room temperature).
ELECTRICAL FAULT:
If the control display (9) fl ashes together with
the function button (2) LED display or only the
control display (8) fl ashes there is an electrical
fault. The machine cannot be started.
In this case please contact your dealer.
FAULT CHECK LIST:
Should the machine not work, check the following
points:
- is the plug connected to the power supply?
- is the waste bin pushed in?
- is the waste bin (14) full?
Follow the instructions under “EMPTYING THE
WASTE BIN”.
- Is there a material jam in the machine?
Follow the instructions in “MATERIAL JAM IN
THE MACHINE”.
- Is the motor overloaded?
See “MOTOR PROTECTION”.
If none of these test points apply, please
contact your dealer.
315SC2 315CC3 315CC4 319SC2 319CC3 319CC4
7
MALFUNCTIONS
To remove these paper strips and also to clean the
photocell, pass another sheet of paper through the
feed slot, or switch the machine to reverse and wipe
both “eyes” of the photocell with a brush.
CUTTER MAINTENANCE (CROSS CUT):
Cross cut cutters must be oiled after a
specifi c operating time. If the control display
(7) comes on proceed as follows:
Pour a little oil onto a sheet of paper and then feed this
through the paper feed slot (12) onto the cutters. The
paper is drawn in and in this way the oil is distributed
to the cutters.
Note: This procedure is acknowledged as follows
to turn off the display after the cutters have been
oiled:
- Press the reverse button (4) and keep it held
down until the control display (7) goes out.
CLEANING THE PHOTOCELLS (Fig. 5):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier. The cutters now start a cleaning cycle automatically
(forward and reverse run) and then switch off. The
machine is ready for use again. Should you need to re-
order the special oil see “SPECIAL ACCESSORIES”.
AUTOMATIC ENERGY SAVING:
If the machine is not used for a while it automatically
switches off after about 5 minutes. The function button
(2) LED display for “Ready” goes out. Press the
function button briefl y to turn it on again.
DISPOSING OF THE MACHINE:
Dispose of the machine in an environmentally
friendly fashion at the end of its useful service
life. Do not dispose of any of the parts
included in the machine or its packaging with
household waste.
MAINTENANCE / DISPOSING
* based on A4-paper 70g/m² at 230V/50Hz – 10%
Model Power supply data
supply voltage / frequency / current consumption
intimus 315/319SC2 220-230V/50Hz, 7.8 amps 115-125V/60Hz, 14.9 amps 100V/50/60Hz, 18.0 amps
intimus 315/319SC2 220-230V/50Hz, 7.8 amps 115-125V/60Hz, 14.9 amps 100V/50/60Hz, 18.0 amps
intimus 315/319CC3 220-230V/50Hz, 7.8 amps 115-125V/60Hz, 14.9 amps 100V/50/60Hz, 18.0 amps
intimus 315/319CC4 220-230V/50Hz, 7.8 amps 115-125V/60Hz, 14.9 amps 100V/50/60Hz, 18.0 amps
Model Cutting width Cutting capacity Working width Power Noise level Intermittent operation Dimensions Weight
paper / CD,DVD paper / CD,DVD ON / OFF W x D x H
intimus 315/319SC2 5.8 mm / 8 mm 35-38 sheets* / 1 piece 310 mm 1.8 kW app. 57 dB(A) 45 / 60 min 790 x 926 x 1297 mm 81/98 kg
intimus 315/319SC2 3.8 mm / 8 mm 31-33 sheets* / 1 piece 310 mm 1.8 kW app. 57 dB(A) 45 / 60 min 790 x 926 x 1297 mm 81/98 kg
intimus 315/319CC3 3.8x36 mm/ 8 mm 23-25 sheets* / 1 piece 310 mm 1.8 kW app. 57 dB(A) 45 / 60 min 790 x 926 x 1297 mm 82/99 kg
intimus 315/319CC4 1.9x15 mm / 8 mm 15-17 sheets* / 1 piece 310 mm 1.8 kW app. 57 dB(A) 45 / 60 min 790 x 926 x 1297 mm 82/99 kg
TECHNICAL DATA
SPECIAL ACCESSORIES
Description Order-No.
Lubricant, 110 ml bottle
88035
Note: For orders of special accessories and spare
parts, please contact your dealer.
fi g. 5
GB
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung