Global Specialties PB-505 - Data Sheet - Manual (Page 2)

PB-505
Specifications
Innovative Training Solutions
www.globalspecialties.com
© 2011 Global Specialties V102109 22820 Savi Ranch Parkway Yorba Linda, CA 92887 1.800.572.1028
Optional Accessories
Courseware: Available separately or as a
package (Model PB-505 Lab).
WK-1: Jumper Wire Kit, 350 pieces
WK-2: Jumper Wire Kit, 140 pieces
WK-3: Jumper Wire Kit, 70 pieces
WK-4: Wire Jumper Kit, 100 wires with
machined tips
GSPA Series: Prototyping adapters
GSPA-K1: Surface mount to DIP adapter
kit, 6 adapter boards
GSPA-K2: Surface mount to DIP adapter
kit, 11 adapter boards
GSA-3185: Minipro Test Clip Set
PRO-50A: Digital Multimeter
The PB-505 Lab package offers
comprehensive course instruction
covering the following areas:
Electronic Fundamentals
Fundamentals of Electricity
Ohm’s Law
Series Circuits, Parallel Circuits
Combinational Circuits
Current Control
Closed, open, shorts
Switches
Thevenin’s Theorem
Wheatstone Bridge
Capacitors, Inductors
Phase Shift Circuits
Impedance
Resonant Circuits
Transformers
Rectifiers & Filtering
Integrated Circuits
Transistor Amplifiers
Oscillators
Power Control Circuits
Digital Electronics
Number Systems & Codes
Binary, Decimal, Hexadecimal, Octal &
ASCII
Logic Gates & Boolean Algebra
Combinational Logic Circuits
Flip-Flops
Digital Arithmetic
Counters & Registers
Integrated Circuit Logic Families
TTL Logic
MOSFETS
CMOS
Interfacing CMOS & TTL
Medium Scale Integration
Decoders
Encoders
Data Conversion & Acquisition
Microcomputer Concepts
Advanced
Analog &
Digital
Design
Workstation
Model
PB-505
Input power
Source
Input Power Source, AC Line: Switchable
between 110-120VAC @ 60Hz & 210-220VAC
@50Hz
Power Supplies
Fixed DC: +5VDC 1.0A max, current limited
Ripple, <5mV
Variable + DC: +1.3V @150mA to +15VDC @
500mA , Ripple < 5mV
Variable - DC: -1.3VDC @ 150mA to -15VDC @
500mA, Ripple < 5mV
Binding Posts
(4) Ground, +5 VDC, Variable + DC & Variable -
DC Power Supply Outputs
Pulsers
(2) Pushbutton-operated, open-collector output
pulsers. Each with 1 normally-open, 1 normally-
closed output. Each output sinks up to 250 mA
Logic Probe
Detects Logic High, Logic Low and Single Shot
events.
Logic High: 2.2V (nominal) in TTL mode, 70%
of Vcc in CMOS mode.
Logic Low: 0.8V in TTL mode, 30% of Vcc in
CMOS mode.
Memory Mode: Detects single shot events and
holds indication until Pulse/Mem switch is
toggled
Function
Generator
Frequency Range: 0.1Hz to 100KHz, six ranges
Output Voltage: 0 to + 10Vp-p into 50 Ω Load
(20Vp-p in open circuit), short circuit protected
Output Impedance: 600Ω except TTL
Output waveforms: Sine, Square, Triangle & TTL
Sine Wave Distortion: <3% @ 1Khz Typical
TTL Pulse: Rise & fall time: <25ns, drive 10 TTL
Loads (TTL available when function generator is
set to Square Wave Mode)
Square Wave: Rise and fall times <0.5µs
Logic Switches
(8) Logic Switches select Logic High and Logic
Low
Logic Low Level: Ground
Logic High Level: Switchable between +5V and
the variable positive power supplies.
Switches
(2) Single Pull Double Throw (SPDT) -
uncommitted
Logic
Indicators
LEDs: 16 LEDs; (8) red to indicate logic high and
(8) green to indicate logic low
Logic High Threshold: 2.2V (nominal) in TTL/+5V
mode, 70% (nominal) of selected operating
voltage in CMOS mode
Logic Low Threshold: 0.8V (nominal) in TTL/+5V
mode, 30% (nominal) of selected operating
voltage in CMOS mode
Connectors 2 ea BNC - uncommitted
Potentiometers 2: 1 kΩ and 10 kΩ - uncommitted
Speaker 8 Ω, 0.25 W - uncommitted
Displays
(2) BCD to 7 Segment Display Circuits include
(20 red LEDs and decoder/driver circuitry
Breadboards
Removable Plexiglas Socket Plate (PB-3) with
2520 Tie points with 200 additional buss strip tie
points internally connected to power supply
outputs and ground
Weight 10 lbs (4.6 kg)
Dimensions 6.5 x 19 x 11.5" (165 x 482 x 292 mm)
Technical data subject to change without notice.
Trainer Series
Electronic Trainers