Speaker – BeStar BMS40-12-100H5.2 LF User Manual
Page 7
REV.
Drawn
Date
6
5
A
Speaker
Date:
Note
Approved by:
4
Drawn by:
Checked by:
3
2
Page:6 of 9
1
A
B
C
D
E
F
G
H
B
C
T
h
is
p
ri
n
t
a
n
d
i
n
fo
rm
a
tio
n
t
he
re
i
n
a
re
p
ro
p
ri
e
ta
ry
t
o
B
e
s
ta
r
E
le
c
tr
o
n
ics
I
ndu
s
tr
y
C
o
.,
L
td.
a
nd
s
h
a
ll
no
t
b
e
u
s
ed
i
n
w
h
o
le
o
r
in
pa
rt
w
ith
ou
t
it
s
w
ri
tt
en
c
on
tent
D
E
F
G
H
5
6
4
2
3
1
A
06/9/8
付 静
程久生
莫丽丽
莫丽丽
16.WCR 00.00EA-D11-30/Table3.3/4.5.10Dust
Expose the component to 100mg/m3 for 5 hours or 3,000 mg/m3 or 60,000
mg/m3 dust concentration (as specified) for 8 hours.
Notes:
(1)The component shall be operating or non - operating throughout the test
as required.
(2)In the event that SAE J1211 or IEC529 test procedures are specified.
"equivalent" or greater dust concen -trations and test duration requirements
must be applied.Above stated test parameters are directly applicable to test
equipment designed to JIS D0207 specifications.
17.WCR 00.00EA-D11-34 /Table4.(a) /4.7.1Salt Mist Atmosphere
Temperature +35℃,Duration : 48hrs
Expose the component to salt mist atmosphere(from 5% salt water solution at
35℃) for 48 hours.
18.WCR 00.00EA-D11-34 /Table4.(a) /4.7.2 Chemical Resistance
Brush the specified chemical solutions onto the component and then leave at
maximum storage temperatire T6 +85℃for 96 hours.Note:test may be waived is using.
Ford approved materials.
19.WCR 00.00EA-D11-33 /Table4.(a) /4.6.3.4Low Machanical Shock
Subject the component to six 50g (490m/s2) 10ms half-sine shock pulses,
one in each opposite direction of each perpendicular axis.
20.WCR 00.00EA-D11-27 /Table4.(a) /4.5.7Thermal Shock Endurance
1000 thermal shock cycles(non-operating) between minimum and maximum storage
temperatures T5-40℃and T6+85℃as shown below.
21.WCR 00.00EA-D11-34 /Table4.(a) /4.8.1High Temperature Endurance
The testing temperature use the maximum operating temperature T2:+85 ℃,and normal
load stress condition for 1000 hours
22.WCR 00.00EA-D11-34 /Table4.(a) /4.8.4 85/85 High Temperature-High Humidity Endurance
Operate the component at +85℃and 85% RH, and normal load stress condition
for 1000 hours
BMS40-12-100H5.2 LF
BMS40-12-100H5.2 LF
-40℃
85℃
30min
30min
5 min
max
5 min
max
1 cycle
DRG NO: BS/TES01.644D
朱成兴
D
07/03/06
07/03/06