Gorman-Rupp Pumps SFV3A 1473393 and up - Manual (Page 32)

ITEM
NO. PART NAME PART
NUMBER MAT'L
CODE QTY ITEM
NO. PART NAME PART
NUMBER MAT'L
CODE QTY
OM-06396 SF SERIES
PAGE E - 5 MAINTENANCE AND REPAIR
47111-801, -804, -805 and -851 Motor Assemblies
Parts List
1 MOTOR SUBASSEMBLY
-208‐230/3
47111-829 --- 1
--MOTOR HOUSING 38311-065 10000 1
--STATOR 47113-089 --- 1
--TERMINAL HSG STUD MC1042 17000 4
--VOLTAGE TAG 38816-094 --- 1
--ROTATION DECAL 38815-027 --- 1
-460/3 47111-828 --- 1
--MOTOR HOUSING 38311-065 10000 1
--STATOR 47113-089 --- 1
--TERMINAL HSG STUD MC1042 17000 4
--VOLTAGE TAG 38816-093 --- 1
--ROTATION DECAL 38815-027 --- 1
-575/3 47111-830 --- 1
--MOTOR HOUSING 38311-065 10000 1
--STATOR 47113-090 --- 1
--TERMINAL HSG STUD MC1042 17000 4
--VOLTAGE TAG 38816-128 --- 1
--ROTATION DECAL 38815-027 --- 1
-230/1 47111-852 --- 1
--MOTOR HOUSING 38311-065 10000 1
--STATOR 47113-105 --- 1
--TERMINAL HSG STUD MC1042 17000 4
--VOLTAGE TAG 38816-098 --- 1
--ROTATION DECAL 38815-027 --- 1
2 BEARING S1905 --- 2
3 . ROTOR/SHAFT ASSY (208‐230/460/575V 3P)
47112-084 --- 1
. ROTOR/SHAFT ASSY (230V 1P)
47112-091 --- 1
4 BEVELED SNAP RING 24121-526 --- 1
5 O‐RING 25152-264 --- 1
6 PIPE PLUG P06 17000 2
7 INTERMEDIATE 38261-034 10000 1
8 SEAL ASSY S1575 --- 1
9 CENTERING WASHER 31161-045 17000 1
10 SNAP RING S987 --- 1
11 LOCK WASHER MJ10 17000 8
12 HEX HD CAPSCREW MB1025 17000 8
13 MOISTURE DETECTOR 27479-008 --- 1
14 FEMALE TERMINAL 27236-054 --- 1
15 MALE TERMINAL 27236-454 --- 1
16 IMPELLER KEY MN0520 17000 1
17 36” 18 AWG WIRE 18147-104 --- 1
NOT SHOWN (SUPPLIED WITH MOTOR SUBASSEMBLY):
WIRE CONNECTOR S1718 --- 3
POWER LEAD CONTACTS:
-208‐230/460/3
27216-004 --- 3
-575/3 27216-004 --- 3
POWER LEAD CONTACT HOUSINGS:
-BLACK
27216-034 --- 1
-WHITE 27216-035 --- 1
-RED 27216-036 --- 1
CONT LEAD CONTACT 27216-002 --- 3
CONTROL LEAD CONTACT HOUSINGS:
-ORANGE
27216-032 --- 1
-BLUE 27216-031 --- 1
-BROWN 27216-033 --- 1
INDICATES PARTS RECOMMENDED FOR STOCK
. NOTE: WHEN ORDERING A REPLACEMENT ROTOR/SHAFT ASSY, DETERMINE THE IMPELLER ATTACHEMENT HARDWARE
FOR YOUR PUMP AS SHOWN IN FIGURE 1 AND ORDER REPLACEMENT HARDWARE AS REQUIRED.