Gorman-Rupp Pumps PAH6B60-6068H 1507875 and up - Manual (Page 42)

PAH SERIES OM-06451
MAINTENANCE & REPAIR PAGE E - 20
With the lip seal sleeve in place, lubricate the lip
seal area of the shaft and slide the shaft and as­
sembled bearings into the bearing housing until
the retaining ring on the outboard bearing seats
against the pedestal. Remove the lip seal sleeve.
When installing the shaft and bearings into
the bearing bore, push against the outer
race. Never hit the balls, rollers or cages.
Apply a light coating of oil to the lip of the outboard
oil seal (11) and press it into the pedestal with the
lip positioned as shown in Figure 5. The face of the
oil seal should be just flush with the outer face of
the bearing cap.
Apply a light coating of oil to the lip of the oil seal
(19) and press it into the drive flange (20) with the
lip positioned as shown in Figure 5. The oil seal
should be centered in the flange bore.
Install the gasket (21) and slide the assembled
drive flange and oil seal over the impeller shaft. Use
caution not to cut or roll the lip of the oil seal (19) on
the shaft keyway. Secure the drive flange to the
pedestal with the hardware (15 and 16). Torque the
capscrews (16) to 41 ft. lbs. (5,7 m. kg.).
Lubricate the bearings as indicated in LUBRICA­
TION at the end of this section.
Securing Pedestal And Drive Assembly To
Engine
(Figure 8)
Install the shaft key (28, Figure 5) in the shaft key­
way. Position the flexible portion of the coupling as­
sembly (3) on the shaft as shown in Figure 8.
NOTE
The flexible portion of the coupling must be proper­
ly positioned on the shaft. The heads of the caps­
crews in the center of the coupling must be posi­
tioned away from the pump.
Align the keyway in the bushing (2) with the shaft
key, and slide it onto the shaft until the face of the
bushing is just flush with the end of the shaft. Ro­
tate the flexible portion of the coupling until the
tapped holes for the two setscrews align with those
in the bushing, and install the setscrews.
Make certain that the flexible portion of the
coupling is mounted as shown in Figure 8.
This is critical. If the coupling is not prop­
erly positioned on the shaft, the coupling
parts may not fully engage, or a pre‐load
condition can cause premature bearing
failure.
The end of the shaft must be extend 0.44
inch (11,2 mm) from the face of the
bushing. This will allow the two portions of
the coupling to fully engage when the en­
gine bracket is secured to the engine bell­
housing without pre‐loading the bearings.
With the flexible portion of the coupling and the
bushing properly positioned on the shaft, tighten
the two setscrews in an alternating sequence until
the bushing and coupling are fully secured. Torque
the setscrews to 67 ft. lbs. (800 in. lbs. or 0,57 m.
kg.).
If the complete coupling assembly is being re­
placed, apply `Loctite Retaining Compound No.
242' or equivalent to the threads of the hardware (4
and 5) and secure the outer ring of the coupling to
the engine flywheel by torquing the hardware to 50
ft. lbs. (6,9 m. kg.).
Using a suitable lifting device, position the as­
sembled drive and rotating assembly so the flex­
ible portion of the coupling seats inside the outer
ring attached to the engine flywheel.
NOTE
To ease installation, lightly lubricate the rubber por­
tion of the coupling with a non‐petroleum based
lubricant such as vegetable oil or glycerin, or a sili­
con‐based lubricant such as “WD40” or equivalent.
Do not use petroleum‐based lubricants, or any oth­
er substance which may soften or otherwise dam­
age the rubber.