beautypg.com

Gorman-Rupp Pumps 13A52-GX390 1371656 and up User Manual

Page 25

background image

OM−04730

10 SERIES

MAINTENANCE & REPAIR

PAGE E − 7

ware (13, 14, 15, and 16, Figure 1) securing the
pump casing to the rollover base (3, Figure 1).

Support the pump casing using a suitable hoist
and sling, and remove the nuts (10) securing the
pump casing to the intermediate (13). Separate the
parts by pulling the casing straight away from the
intermediate. If shims have been used under the
mounting feet to level the pump casing, tie and tag
these shims.

Remove the casing gasket set (8). Record the
thickness of the gaskets or tie and tag them for fu-
ture reference. Clean the mating surfaces of the in-
termediate and pump casing.

Impeller Removal

(Figure 2)

To loosen the impeller (2), tap the vanes of the im-
peller in a counterclockwise direction (when facing
the impeller) with a block of wood or a soft-faced
mallet. Unscrew the impeller and replace it if
cracked or badly worn. Use caution when remov-
ing the impeller; tension on the seal spring will be
released as the impeller is unscrewed.

Slide the impeller adjusting shims (37) off the im-
peller shaft. Tie and tag the shims or measure and
record their thickness for ease of reassembly.

Seal Removal and Disassembly

(Figures 2 and 3)

Remove the spring centering washer and seal
spring. Slide the shaft sleeve (36) and rotating por-
tion of the seal off the shaft as an assembly. Lubri-
cate the sleeve adjacent to the seal and work oil up
under the rubber bellows. Slide the rotating portion
of the seal off the shaft sleeve.

Remove the nuts (12) and carefully slide the inter-
mediate (13) and stationary portion of the seal off
the shaft as a unit. Use a suitably sized dowel to
press the stationary element out of the intermedi-
ate from the back side.

NOTE

The seal assembly may be removed without com-
pletely disassembling the pump by using a pair of
stiff wires with hooked ends to pull the seal station-
ary seat out of the intermediate.

If no further disassembly is required, see Seal
Reassembly and Installation.

Seal Reassembly and Installation

(Figures 2 and 3)

Clean the seal cavity and shaft with a cloth soaked
in fresh cleaning solvent.

Most cleaning solvents are toxic and
flammable. Use them only in a well ven-
tilated area free from excessive heat,
sparks, and flame. Read and follow all
precautions printed on solvent contain-
ers.

The seal is not normally reused because wear pat-
terns on the finished faces cannot be realigned
during reassembly. This could result in premature
failure. If necessary to reuse an old seal in an emer-
gency, carefully wash all metallic parts in fresh
cleaning solvent and allow to dry thoroughly.

Handle the seal parts with extreme care to prevent
damage. Be careful not to contaminate precision
finished faces; even fingerprints on the faces can
shorten seal life. If necessary, clean the faces with a
non-oil based solvent and a clean, lint-free tissue.
Wipe lightly in a circular pattern to avoid scratch-
ing the faces.

Inspect the seal components for wear, scoring,
grooves, and other damage that might cause leak-
age. Clean and polish the shaft sleeve, or replace it
if there are nicks or cuts on either end. If any com-
ponents are worn, replace the complete seal;
never mix old and new seal parts.

If a replacement seal is being used, remove it from
the container and inspect the precision finished
faces to ensure that they are free of any foreign
matter.

To ease installation of the seal, lubricate the O-
rings, sleeve and bellows with water or a very small
amount of oil, and apply a drop of light lubricating
oil on the finished faces. Assemble the seal as fol-
lows (see Figure 3).