New construction, Operational check, Nx-w6.2-x specifications – NXG Technology NX-W6.2-X User Manual

Page 2: Warranty service, Nxg speakers three-year limited warranty, Limitation of implied warranties, Exclusion of certain damages, This warranty does not cover

Warranty Service

Warranty service must be performed by an authorized service

center, usually a NXG speaker systems dealer or its authorized

agent. You may obtain a list of authorized service centers by con-

tacting NXG. All warranty repairs must be accompanied by the orig-

inal bill of sales. No other document is acceptable or is required.

This warranty gives you specific legal rights, and you may also have

other rights which vary from state to state.

NXG reserves the right to revise speaker system specifications

without notice.

(Continued from front)

NXG Speakers Three-Year Limited Warranty

If the NXG speaker system proves to be defective in workmanship or materials within three years

from the date of the original customer’s purchase, we will, at our option, repair or replace the

defective product.

Limitation of Implied Warranties

Any implied warranties, including warranties of merchantability and fitness for a particular purpose,

are limited in duration to the length of this warranty.

Exclusion of Certain Damages

NXG’s liability for any defective product is limited to repair or replacement of the product at our

option. NXG shall not be liable for incidental or consequential damages of any kind or character

because of product defects. Some states do not allow limitations on how long an implied warranty

lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitations and exclusions may not apply.

5. Attach the wire to the input terminals on the rear

of the speaker. Remember to maintain proper polarity

with the amplifier by attaching the positive (+) lead to

the red terminal and the negative (-) lead to the black

terminal.
6. See Fig. 5. With the speaker wire attached to the

speaker, slide the speaker up inside the cut-out hole.

Center the speaker in the cut-out hole and turn the

six locking screws clockwise until the speaker is

drawn up snugly to the wall board from behind,

clamping the speaker in place. Try to tighten each

screw equally. Replace the speaker grill by gently

pressing it into place.

New Construction

1. Determine speaker locations and mark them on

your plans for future reference.
2. If possible, run speaker wires after HVAC and

electrical wiring is in place.
3. Secure speaker wires in place along the run

with insulated staples only and be careful not to

pierce the wire’s insulation. Allow a bit of slack for

expansion of building materials.
4. Needless to say, the actual speakers should not

be installed until the wall board is in place. In the

meantime, leave several feet of wire coiled up and

secured at the back side of the mounting hole.
5. To complete the installation follow steps 2

through 5 above.

Operational Check

After making all connections it’s a good idea to make

sure every thing is working properly. Turn on your

surround or stereo system making sure the volume

control is turned down and that the balance control is

in the center position. Activate a musical or movie

source such as FM, a CD or DVD player. Gently turn

up the volume, you should hear sound coming from

your new NXG speakers. If no sound is heard from

any or all speakers, switch off the system immediately

and check for open or loose connections, wrong polar-

ity or shorts, or proper source selection.

FIG. 5

16648 North 94th Street

Scottsdale, AZ 85260

1-800-733-0008

This Warranty Does Not Cover:

• Damage caused by abuse, accident, misuse, negligence, or improper operation.

• Any product whose serial number has been altered, defaced, or removed.

• Products that have been altered or modified.

• Normal wear and maintenance.

• Damages caused by shipping. (All claims for shipping damage must be made with the carrier.)

FIG. 4

NX-W6.2-X Specifications

Maximum Power Handling: 5 - 150 watts

Sensitivity: 90dB @ 1 watt/1 meter

Frequency Response: 50 Hz-22,000 Hz

Driver Complement:

˝ (165mm) compression-molded mineral-filled polymer cone woofer with rubber surround

1˝ (25mm) pivoting liquid-cooled soft dome tweeter

Nominal Impedance: 8 ohms

Overall Dimensions: 12

˝ H x 8

˝ W x 3

˝ D (308 mm x 222 mm x 89 mm)

Required Wall Cutout: 10

˝ H x 7

˝ W (276 mm x 187 mm)