NXG Technology NX-552CLR - Manual (Page 2)

FIG. 5
(Continued from front)
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship or materials
within three years from the date of the original customer’s purchase, we will,
at our option, repair or replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness
for a particular purpose, are limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of
the product at our option. NXG shall not be liable for incidental or consequential
damages of any kind or character because of product defects. Some states do
not allow limitations on how long an implied warranty lasts and/or do not allow
the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusions may not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper
operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be
made with the carrier.)
Warranty Service
Warranty service must be performed by an authorized service center, usually
an NXG speaker systems dealer or its authorized agent. You may obtain a list of
authorized service centers by contacting NXG. All warranty repairs must be
accompanied by the original bill of sales. No other document is acceptable or
is required. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
NXG reserves the right to revise speaker system specifications without notice.
New Construction
1. Determine speaker locations and mark them on your plans for
future reference.
2. If possible, run speaker wires after HVAC and electrical wiring
is in place.
3. Secure speaker wires in place along the run with insulated
staples only and be careful not to pierce the wire’s insulation. Allow
a bit of slack for expansion of building materials.
4. Needless to say, the actual speakers should not be installed
until the wall board is in place. In the meantime, leave several feet of
wire coiled up and secured at the back side of the mounting hole.
5. To complete the installation follow steps 2 through 5 above.
FIG. 4
6. See Fig. 5. With the speaker wire attached to the speaker, slide
the speaker up inside the cut-out hole. Center the speaker in the
cut-out hole and turn the six locking screws clockwise until the
speaker is drawn up snugly to the wall board from behind, clamp-
ing the speaker in place. Try to tighten each screw equally. Replace
the speaker grill by gently pressing it into place.
Operational Check
After making all connections it’s a good idea to make sure everything is working
properly. Turn on your surround or stereo system making sure the volume control
is turned down and that the balance control is in the center position. Activate a
musical or movie source such as FM, a CD or DVD player. Gently turn up the vol-
ume, you should hear sound coming from your new NXG speakers. If no sound
is heard from any or all speakers, switch off the system immediately and check for
open or loose connections, wrong polarity or shorts, or proper source selection.
Specifications
Woofers: Two magnetically-shielded 5 1 /
4
˝ (133mm) aluminum
anodized injection-molded cones with rubber surrounds
Tweeter: Pivoting liquid-cooled 1˝ (25mm) soft dome
Frequency Response: 50 Hz-22,000 Hz
Impedance: 8 ohms nominal
Power Handling: 5 -120 watts
Efficiency: 90dB @ 1 watt/1 meter
Dimensions: 17 3 /
4
˝ W x 8 3 /
4
˝ H x 3˝ D
16648 North 94th Street • Scottsdale, AZ 85260
1-800-733-0008