Media-Tech MEGA DROIDER IR User Manual

Page 2

4. If the device you are searching for is a CD player,

Tuner, TAPE, or AUX, a power signal is automatically
transmitted from the remote control to the device.
As soon as the device turns oﬀ , press the device key
to stop the Search. You need to turn on the device
by pressing the Power button before you can check
the functions of the other buttons.

5. Check the functions of the other buttons on the

remote control. If none of the buttons function (i.e.
the search cannot be stopped at the correct time)
or the majority of the buttons do not function cor-
rectly, restart the search (see steps 2 to 4) to ﬁ nd a
suitable code. If the majority of the buttons func-
tion correctly, set- up has been successful. Re-press
the device button (for instance TV) to save the code
and to terminate the set-up mode.

C. Set up by Manual Search

If setting up with brand name and codes is unsuccess-
ful, you can also use the “Manual Search” to ﬁ nd the
correct code for operating your device.

1. Switch on the device that you like to control. If it is a

VCR, please insert a cassette.

2. Point the remote control at the device. Press and

hold the device button (for instance TV) for 3 sec-
onds. The LED lights up and the remote is in manual
set-up mode, release the device button now.

3. Press the “Volume+” button approx. every 1.5 seconds.

4. As soon as the volume of the device (for instance

TV) changes or the device turns oﬀ , check whether
the other buttons on the remote control function
correctly. If the majority of the buttons does not
function correctly, press the Volume+ approx. every
1.5 seconds to initiate the reactive code ( manual
search is continued, see step 3 to 4). If the majority
of the buttons on the remote control functions cor-
rectly, save the code by pressing the device button
(for instance TV) to terminate the manual search.

Note: The Manual Search is automatically terminat-
ed if no entry occurs during a 30 seconds period.

D. Setup By Using The Learning Function

The Learning Function is used to extend the pre-
programmed codes by transferring codes from your
existing remote control to the keyboard remote. The
standard code list already provides you with the most
important functions, but it is possible to add a few ad-
ditional functions. A fully functional original remote
control is required for the keyboard remote to learn
programming. Please use fresh batteries for both the
keyboard remote and the original remote control.

1. Press and hold the ‘Device’ button which you want

to learn (for instance DVD), and press the ‘Learn’ but-
ton at the same time. When the LED turns on then
release both keys. Now the remote control is in
Learning Mode for codes.

2. Press and release the target button on your key-

board remote that you want to learn (for instance-
POWER). The LED will start to ﬂ ash. (If no button is
pressed within 14 seconds, Learning Mode will exit
automatically.)

3. Press the button (For example, power button) on your

original remote control. When you see the LED on
your new universal remote control ﬂ ash three times
and stop, it means the device has accepted the new
code and it can now start to learn another new code
from the original remote. (If no button is pressed
within 14 seconds, it will exit learning mode auto-
matically and you will need to restart from step 1.)

4. Repeat steps 2 to 4 to learn another code from the

original remote control.

5. When you ﬁ nish learning all the buttons that you

want the keyboard remote to know, press the ‘Learn’
button to store all commands you have learned
from the original remote and to exit Learning mode.

6. Press the ‘TV’ button and ‘Number 6’ at the same

time to delete all the codes you have learned for all
devices.

Note:
1. Point the IR transmitter of the original remote

control to face the IR receiver of the keyboard re-
mote with approximately 30mm between them.
Hold the two remotes in a straight line to make
the learning process more accurate.

2. When you cannot choose any more buttons on

the new universal remote control for learning, it
means the memory is full.

E. Display the code

1. Press and hold the device button ( TV) and simulta-

neously press button 1 to display the thousands of
the 4-digit code. Count how often the LED ﬂ ashes, if
the LED does not ﬂ ash, the number is zero.

2. Press and hold the device button (TV), simultane-

ously press button 2 to display the hundreds of the
4-digit code, Count how often the LED ﬂ ashes, if the
LED does not ﬂ ash, the number is zero.

3. Press and hold the device button (TV), simultane-

ously press button 3 to display the tens of the 4-digit
code, Count how often the LED ﬂ ashes, if the LED
does not ﬂ ash, the number is zero.

4. Press and hold the device button (TV), simulta-

neously press button 4 to display the ones of the
4-digit code, Count how often the LED ﬂ ashes.

For example for Code 0169

1. Press TV and 1 LED ﬂ ashes zero times
2. Press TV and 2 LED ﬂ ashes one time
3. Press TV and 3 LED ﬂ ashes six times
4. Press TV and 4 LED ﬂ ashes nine times

F. Reset / Delete Function

Simply press the device (TV) button and Button 0 to-
gether, when the LED ﬂ ashes three times, all settings
will be deleted, and the remote goes back to factory
default settings.

Speciﬁ cation and appearance of product are subject to
change without prior notice. For technical support please
visit www.media-tech.eu.