Aqua-Pure 3MFF100 - Manual (Page 3)

SAFETY INFORMATION
EXPLANATION OF SIGNAL WORD CONSEQUENCES
Read, understand, and follow all safety information contained in these instructions prior to
installation and use of this Full Flow Drinking Water System Model 3MFF100. Retain these
instructions for future reference.
Intended use:
The Full Flow Drinking Water System is intended for use in fi ltering potable water in homes and has not been
evaluated for other uses. Model 3MFF100 is installed at the point of use and typically installed under a sink.
System must be installed as specifi ed in the installation instructions by a qualifi ed professional.
C CAUTION
WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in
death or serious injury and/or property damage.
Indicates a potentially hazardous situation, which, if not avoided, may result in
property damage.
WARNING
To reduce the risk associated with choking:
•
Do not allow children under 3 years of age to have access to small parts during the installation of this product.
To reduce the risk associated with ingestion of contaminants:
•
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after
the system. Systems certifi ed for cyst reduction may be used on disinfected water that may contain fi lterable cysts. EPA
Establishment #070595-CT-001.
To reduce the risk associated with a hazardous voltage due to an installer drilling through existing electric wiring or
water pipes in the area of installation:
•
Do not install near electric wiring or piping which may be in the path of a drilling tool when selecting the position to mount
the fi lter bracket.
CAUTION
To reduce the risk associated with property damage due to water leakage:
•
Read and follow Use Instructions before installation and use of this system.
• Installation and use MUST comply with all state and local plumbing codes.
• Protect fi lter from freezing, remove replacement fi lter when temperatures are expected to drop below 40°F (4.4°C).
• Do not install systems in areas where ambient temperatures may go above 110°F (43.3°C).
• Do not install on hot water supply lines. The maximum operating water temperature of this fi lter system is 100°F (37.8°C).
• Do not install if water pressure exceeds 125 psi (862 kPa). If your water pressure exceeds 80 psi (552 kPa), you must
install a pressure limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure.
• Do not install where water hammer conditions may occur. If water hammer conditions exist you must install a water hammer
arrester. Contact a plumbing professional if you are uncertain how to check for this condition.
• Where a backfl ow prevention device is installed on a water system, a device for controlling pressure due to thermal expan-
sion must be installed.
• Do not use a torch or other high temperature sources near fi lter system, cartridges, plastic fi ttings or
plastic plumbing.
• On plastic fi ttings, never use pipe sealant or pipe dope. Use PTFE thread tape only, pipe dope properties may deteriorate plastic.
• Do not install in direct sunlight or outdoors.
• Do not install near water pipes which will be in path of a drilling tool when selecting the position to mount the bracket;
• Mount fi lter in such a position as to prevent it from being struck by other items used in the area of installation (waste baskets, etc.);
• Ensure that the location and fasteners will support the weight of the system when installed and full of water.
• Ensure all tubing and fi ttings are secure and free of leaks.
• Do not install unit if collet is missing. Contact 3M Purifi cation Inc. if collets are missing from any fi ttings.
• The disposable replacement fi lter
MUST be replaced every 12 months, at the rated capacity or sooner if a noticeable
reduction in fl ow rate occurs.
IMPORTANT NOTES
• Failure to follow instructions will void warranty.
• Allow a minimum of 3” (7.6 cm) clear space under fi lter to facilitate fi lter change.
• Install with the inlet and outlet ports as labeled. Make sure not to reverse connections.
1
INSTR2214 0412.indd 1 4/6/2012 9:56:30 AM