Dexter Laundry T-80 Non-reversing (On-Premise) - Manual (Page 18)

- 18 -
3) Press and release the UP touch pad switch on the dryer controller 10 times so that the display will show a
flashing “45”. When the UP touch pad switch is pressed the first time, the number “36” will be flashing on
the dryer controller display. Each number after that will also flash.
4) Now, press and release the SELECT/ENTER touch pad switch on the dryer controller. The number “45”
will stop flashing, the dry time L.E.D. will switch off, the dryer controller display will now show “180”, the
temperature L.E.D. will illuminate, and the programming L.E.D. and dry cycle 1 L.E.D. will remain on.
5) Press and release the UP touch pad switch on the dryer controller one time so the controller display will
show a flashing “185”. Each press of the UP touch pad switch will increment the temperature by five
degrees.
6) Now, press and release the SELECT/ENTER touch pad switch on the dryer controller. The number “185”
will stop flashing, the temperature L.E.D. will switch off, the dryer control display will now show a number “5”,
the cool down L.E.D. will illuminate, and the programming L.E.D. and dry cycle 1 L.E.D. will remain on.
7) Press and release the SELECT/ENTER touch pad switch on the dryer controller, since the desired cool
down time is five minutes. After you press the SELECT/ENTER touch pad switch, the cool down L.E.D.
and programming L.E.D. will switch off, the controller display will remain at “5”, and the cycle 1 L.E.D. will
remain on.
You are now ready to start the new dry cycle. The new dry cycle will be in effect for one dry cycle only.
After the dry cycle is done, or if the STOP touch pad switch on the dryer controller is pressed and released
twice, consecutively, the cycle 1 program will revert to the factory default settings.
If you press the START touch pad switch on the dryer controller, the controller display will change from
the number “5” to the number “45” and dry cycle 1 will begin.
PERMANENT DRYER CONTROLLER PROGRAMMING
The permanent programming mode will allow the change of the stored dry cycle settings in the dryer
controller until the operator physically changes them again. The factory default settings can be restored in the
dryer controller by pressing the default settings push-button on the back (component) side of the dryer controller
circuit board. It is labeled and located at the lower middle side of the printed circuit board, as you face the
component side of the board. It must be pressed and held down for at least three seconds.
To permanently change a dryer controller cycle, follow the procedure below. Things that are displayed on
the 4-digit numeric display will be in “quotation marks”. Touch pad switches on the dryer controller that
physically need to be pressed will be in CAPITAL AND BOLD LETTERS.
If, at any time, you want to escape the permanent programming mode while changing the settings, you can
press the STOP touch pad switch on the dryer controller if the 4-digit numeric display is not flashing. The
SELECT/ENTER touch pad switch on the dryer controller can be pressed and released to enter the flashing
value shown on the 4-digit numeric display and allow you to escape.
PROCEDURE
1) Make sure the dryer is not in a dry cycle. The 4-digit numeric display on the dryer controller will show “LOAd”
when the dryer is not in a dry cycle.
2) Press and release the PROG touch pad switch on the dryer controller.
3) Press and release the UP touch pad switch on the dryer controller. The programming L.E.D. will illuminate
and the 4-digit numeric display on the dryer controller will change to “Prog”.
4) Press and release either the UP or DOWN touch pad switch to choose the dry cycle you want to change
(dry cycle 1 through 5). The dry cycle L.E.D. will illuminate to indicate which dry cycle you are choosing. If
you press and hold down either the UP or DOWN touch pad switch, the controller will sequence through
the five dry cycles.
5) Press and release the SELECT/ENTER touch pad switch once you have chosen the dry cycle you want to
change. After you press the SELECT/ENTER touch pad switch, the dry time L.E.D. will illuminate, the dry