Velleman VDP900HZ - Manual (Page 4)

09.11.201
4. Ins
• Remov
remove
• Clean t
• Place t
• Pour hi
fluid lev
• Connec
5. Use
a) The
• Plug th
power
• Turn on
• The red
• The de
minute
• The gre
Remot
b) The
Please re
1 pow
2
smo
30
3 out
4 fixe
6. Not
The V
pum
• If you e
Check
working
operati
before
• Using t
• A little
7. DMX
a. DMX5
Connect
pin XLR i
cable sho
b. DMX-5
c. DMX S
All DMX-c
This start
Enter the
You can u
device.
0
tallation
ve all packing m
ed.
the spray nozzle
he VDL900HZ
igh quality smok
vel. Do not ove
ct the remote co
e
Device
he remote contro
cord.
n the power swi
d light on the re
vice must warm
es.
een light on the
te Control”).
Remote Contr
efer the illustrat
wer LED
oke output ever
min)
put volume
ed time open LE
tes
VDP900HZ doe
p will continue
experience low
the fluid level, t
g properly, plug
ion to avoid per
transporting th
the device will p
smoke may con
X Connectio
12 Connection
an XLR cable to
nput of the VDP
ould be a two-co
512 Chain with
Start Address
controlled devic
t address is the
e correct numbe
use the same st
aterial from the
e and make sure
horizontally on
ke liquid (VDLH
rfill. Place the c
ontrol into the s
ol into the slot a
itch located at t
emote control w
m up. The period
e remote control
rol
ion on page 2.
ry x minutes (m
ED
es not feature a
e working. Alw
device can su
output, mechan
the external fus
g in the unit aga
rmanent damag
e unit.
produce water d
ntinue to escape
on
n
o the female 3-p
P900HZ. Multip
ore screened ca
h Termination
A DMX term
to run a lon
The termina
noise. The D
between pin
the last dev
ces need a digita
channel numbe
er and read it fro
tarting address
VDP90
4
e shipping box. C
e nothing is obs
a flat surface. R
HLH5) into the t
cap back on the
slot at the back
at the back of th
the back of the
will light up.
d depends on th
l will go up once
5
max. 6
7
8
an automatic
ways monitor t
uffer damage w
nical noise or no
se, the remote c
ain. If the device
e. Return the de
rops at the noz
e from the nozz
pin XLR output o
ple VDP900HZs
able with XLR in
n
minator is recom
g distance or is
ator prevents co
DMX terminator
ns 2 and 3, whic
vice in the chain
al start address
er from which th
om the display
for a whole gro
0HZ
Check that all fo
structing the ou
Remove the liqu
tank, being care
liquid tank and
of the device.
he device. Plug
device.
he conditions bu
e the machine is
output LED
successive s
seconds)
heated over
spray button
stop function
the tank fluid
when run with
o output at all, u
control and the
e will not functi
evice to your de
zle. This is perf
zle after operatio
of your controlle
s can be linked
put and output
mmended for ins
in an electrical
orruption of the
is simply an XL
ch is then plugg
. Please see illu
so that the cor
he device starts
located on the b
oup of devices o
oam and plastic
tput.
uid tank cap.
eful not to excee
tighten.
the device into
ut should not tak
s ready to opera
spraying for x se
r LED
n
when running
level during o
hout fluid!
unplug the devi
power cord. If a
on after 30 seco
ealer. Remembe
fectly normal.
on.
er and the other
through serial l
connectors.
tallations where
ly noisy environ
digital control s
LR plug with a 1
ged into the XLR
ustration.
rrect device resp
s to “listen” to th
base of the VDP
r enter an indiv
©Vellema
c padding is
ed the maximum
the mains usin
ke more than 10
ate (see “The
econds (max. 1
g out of fluid; t
operation as th
ce immediately
all appears to be
onds, discontinu
er to drain the t
r side to the ma
inking. The link
e the DMX cable
nment (e.g. disc
signal by electri
120Ω resistor
R output socket
ponds to the sig
he DMX controll
P900HZ.
vidual one for ev
an nv
m
g the
0
5
the
he
.
e
ue
tank
ale 3-
king
e has
cos).
cal
of
gnals.
ler.
very