Velleman VDP2301RGVLD10 - Manual (Page 9)

VDP2301RGVLD10 - VDP2601RGYLD10 - VDP3801RGVLD10
11/08/2011 ©Velleman nv 9
IMPORTANT NOTE
Setting the projection size to zero can cause a standing laser beam. This is a hazardous
condition that must be avoided at all times.
Showtable:
Note: the show in the first data entry field, DMX value 0, is displayed when the laser projector is paused
or when an empty data location (no filename provided) is opened. For safety reasons it is strongly
advised to leave this empty.
• Enter up to 256 shows into the filename-fields. Click on a filename field to open an explorer dialog box.
Select the desired .ild file.
Note: the .ild file must be on the SD card.
Notes:
• Every show occupies 16 DMX values. The relationship between DMX control and DMX Value (=
filename) is given in the table below:
Showselect H
0-
15
16-
31
32-
47
48-
63
64-
79
80-
95
96-
111
112-
127
128-
143
144-
159
160-
175
176-
191
192-
207
208-
223
224-
239
240-
255
Showselect L
240-255 15 31 47 63 79 95 111 127 143 159 175 191 207 223 239 255
224-239 14 30 46 62 78 94 110 126 142 158 174 190 206 222 238 254
208-223 13 29 45 61 77 93 109 125 141 157 173 189 205 221 237 253
192-207 12 28 44 60 76 92 108 124 140 156 172 188 204 220 236 252
176-191 11 27 43 59 75 91 107 123 139 155 171 187 203 219 235 251
160-175 10 26 42 58 74 90 106 122 138 154 170 186 202 218 234 250
144-159 9 25 41 57 73 89 105 121 137 153 169 185 201 217 233 249
128-143 8 24 40 56 72 88 104 120 136 152 168 184 200 216 232 248
112-127 7 23 39 55 71 87 103 119 135 151 167 183 199 215 231 247
96-111 6 22 38 54 70 86 102 118 134 150 166 182 198 214 230 246
80-95 5 21 37 53 69 85 101 117 133 149 165 181 197 213 229 245
64-79 4 20 36 52 68 84 100 116 132 148 164 180 196 212 228 244
48-63 3 19 35 51 67 83 99 115 131 147 163 179 195 211 227 243
32-47 2 18 34 50 66 82 98 114 130 146 162 178 194 210 226 242
16-31 1 17 33 49 65 81 97 113 129 145 161 177 193 209 225 241
0-15 0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240
• Set the desired frame drawing speed, framerepeat and display mode by clicking on either one of those
fields:
Displaymode
oneshot/complete
The show is shown 1 time completely. It can not be interrupted. When
finished, the projector goes into pause mode.
oneshot/interruptable The show is shown 1 time completely. It can be interrupted via DMX. When
finished, the projector goes into pause mode.
loop/complete The show is shown in a continuous loop. It can only be interrupted at the
end of the show.
loop/interruptable The show is shown in a continuous loop. It can be interrupted at any time
via DMX.