Velleman VDP801GLD10 - Manual (Page 4)

07
•
•
•
•
•
4.
•
•
•
•
•
•
•
•
•
•
•
•
5.
Re
6.
Re
•
/09/2011
Use an app
Familiarise
unqualified
device.
Use the orig
All modifica
Only use th
crash, etc.
. Mountin
Have the de
The carryin
deforming.
The installa
Never stand
technician c
Install the d
Overhead m
material to
device your
Adjust the d
Make sure t
Have a qua
Connect the
The installa
For installat
• Connec
Connect
the male
linking. T
page 2 f
• Chain w
A DMX t
in an ele
signal by
and 3, w
. Descrip
fer to the ill
. Use
fer to the ill
Use the DIP
o
Sound/
auto and
ropriate safe
yourself wit
people. Any
ginal packag
ations of the
he device for
Using the de
ng/conn
evice installe
g constructi
ation must al
d directly be
check the de
device in a lo
mounting req
be used… H
rself if you la
desired inclin
there is no f
lified electric
e device to t
ation has to b
tions using D
ction
t the provide
e 3-pin XLR
The linking c
for pin-out).
with Termin
terminator is
ectrically noi
y electrical n
which is then
ption
ustrations o
1
2
3
4
O
5
6
D
7 DI
8
ustrations o
P switch [7]
/auto/slave
d slave mode
Fun
soun
auto
slav
coun
ety cable to
h the functio
y damage th
ging if the de
device are f
r its intended
evice in an u
necting t
ed by a qual
on must be
lways be sec
elow the dev
evice once a
ocation with
quires exten
Have the mat
ack these qu
nation angle
flammable m
cian carry ou
the mains wi
be approved
DMX512:
ed XLR cable
input of the
cable should
nation
s recommend
sy environm
noise. The D
n plugged int
n page 2 of
MIC
VOLUME
-
ON/OFF*
DMX IN
DMX OUT
IP SWITCH
AC IN ~
n page 2 of
to configure
e mode: swi
e.
nction
nd mode (m
o mode
e mode
ntdown mod
VDP
fix the devic
ons of the de
at may occu
evice is to be
forbidden fo
d purpose. A
unauthorised
he devic
ified person,
able to supp
cured with a
ice when it i
year and on
few passers
sive experie
terial and th
ualifications a
e via the mou
material with
ut the electr
ith the powe
d by an expe
to the fema
laser projec
d be a two-co
ded for insta
ment (e.g. dis
MX terminat
to the XLR o
this manual
micropho
volume c
safety ey
on/off ke
DMX inpu
DMX outp
set the D
AC input
* depen
this manual
e sound or D
itch 10 must
aster)
e*
* the la
P801GLD10
4
ce (e.g. VDL
evice before
ur will most p
e transported
r safety reas
All other uses
d way will vo
ce
, respecting
port 10 times
secondary a
s being mou
nce before yo
s-by that is i
ence: calcula
e device itse
as improper
unting brack
in a 0.5m ra
ric connectio
er plug. Do n
ert before the
ale 3-pin XLR
ctor [5]. Mu
ore screened
allations whe
scos). The te
tor is simply
utput socket
.
one
control
yelet
y switch
ut port (3 pin
put port (3 p
DMX address
110~240Va
nding on the
.
DMX mode:
t be set to th
ser projects
0
LSC7 or VDL
actually usi
probably be
d.
sons.
s may lead t
oid the warra
EN 60598-2
s the weight
attachment
unted, remov
ou bring it in
inaccessible
ting workloa
elf checked r
installation
ket and tight
adius of the d
n.
not connect i
e device is ta
R output of y
ltiple laser p
d cable with
ere the DMX
erminator pr
an XLR plug
t [6] of the
ns)
pins
c 50/60Hz (
e model an a
he OFF posit
DIP Sw
a countdow
LSC8).
ng it. Do no
due to unpr
to short circu
anty.
2-17 and all
t of the devic
e.g. a safety
ved or servic
nto service.
to unauthor
ad limits, det
regularly. Do
may result i
ten the brack
device.
it to a dimm
aken into se
your controll
projectors ca
XLR input a
cable has to
revents corru
g with a 120
last device i
and fuse ho
additional on
tion. Switche
itches
wn sequence
t allow oper
rofessional u
uits, burns, e
other applic
ce for 1 hou
y cable.
ced. Have a
rised person
termining th
o not attemp
in injuries.
ket screws.
ing pack.
ervice.
ler and the o
n be linked
nd output co
o run a long
uption of the
0Ω resistor b
in the chain
lder)
n/off switch m
es 1 and 2 th
from 9 to 0
©Velleman
ation by
se of the
electroshock
able norms.
r without
qualified
s.
he installatio
pt to install t
other side to
through seri
onnectors (s
distance or
e digital cont
etween pins
(see page 2
may be pres
han determin
.
n nv
ks,
n
the
o
ial
see
is
trol
s 2
2).
sent
ne