Wiha Tools Pliers - Manual (Page 46)

Z 41 1 04 Diagonal cutter Professional ESD.
Standards: DIN ISO 9654. IEC 61340-5-1.
Head shape: Wide, pointed head.
Design: Bevelled cutting edges, also appropriate for hard wires.
Maximum service life of cutting edge achieved through additional inductive
hardening to approx. 64 HRC. With opening spring.
Surface resistance 10 6 - 10 9 ohms.
Material: High alloy carbon steel C 60.
Application: All round electronic diagonal cutter for cutting wires
of different hardnesses.
Z 41 3 04 Diagonal cutter Professional ESD.
Standards: DIN ISO 9654. IEC 61340-5-1.
Head shape: Wide, pointed head.
Design: Cutting edge without bevel for absolute flush cutting.
Maximum service life of cutting edge achieved through additional inductive
hardening to approx. 64 HRC. With opening spring.
Surface resistance 10 6 - 10 9 ohms.
Material: High alloy carbon steel C 60.
Application: For absolutely flush cutting of copper wire.
Z 41 4 04 Diagonal cutters Professional ESD
with wire trapping spring.
Standards: DIN ISO 9654. IEC 61340-5-1.
Head shape: Wide, pointed head.
Design: With fixture for trapping ends of wires which have been cut off.
Cutting edge with full flush cutter function for virtually flush cutting.
Maximum service life of cutting edge achieved through additional inductive
hardening to approx. 64 HRC.
With opening spring.
Surface resistance 10 6 - 10 9 ohms.
Material: High alloy carbon steel C 60.
Application: For virtually flush cutting copper wire, function for trapping cut off wire.
275
www.wiha.com
Z 40 1 04 Diagonal cutter Professional ESD.
Standards: DIN ISO 9654. IEC 61340-5-1.
Head shape: Narrow, pointed head.
Design: Bevelled cutting edges, individually tested, also appropriate
for thin, hard wires. Maximum service life of cutting edge achieved through
additional inductive hardening to approx. 64 HRC. With opening spring.
Surface resistance 10 6 - 10 9 ohms.
Material: High alloy carbon steel C 60.
Application: For cutting different hardnesses of wires in places
which are difficult to access.
Z 40 4 04 Diagonal cutter Professional ESD.
Standards: DIN ISO 9654. IEC 61340-5-1.
Head shape: Extra narrow, short head for working
in particularly restricted spaces.
Design: Cutting edge almost without bevel for virtually flush cutting, individually
tested. Maximum service life of cutting edge achieved through additional
inductive hardening to approx. 64 HRC. With opening spring.
Surface resistance 10 6 - 10 9 ohms.
Material: High alloy carbon steel C 60.
Application: For virtually flush cutting copper wire in flat places
which are difficult to access.
Z 40 3 04 Diagonal cutter Professional ESD.
Standards: DIN ISO 9654. IEC 61340-5-1.
Head shape: Narrow, pointed head.
Design: Blade without facet, individually inspected, suited to thin, tough wire.
Maximum service life of cutting edge achieved through additional inductive
hardening to approx. 64 HRC. With opening spring.
Surface resistance 10 6 - 10 9 ohms.
Material: High alloy carbon steel C 60.
Application: For absolutely flush cutting of copper wire in places
which are difficult to access.
10,5
9,5
6,0
13,5
11,5
7,5
10,5
9,5
6,0
13,5
11,5
7,5
13,5
11,5
7,5
10,5
9,5
6,0
Diagonal cutter, broad, pointed shape.
Order-No.
26816 115 4 ½ 1.4 1.0 0.4 60 5
Order-No.
26821 115 4 ½ 1.0 60 5
Order-No.
26822 115 4 ½ 1.2 60 5
Diagonal cutter, narrow, pointed shape.
Order-No.
26808 115 4 ½ 1.0 0.6 0.3 60 5
Order-No.
26814 115 4 ½ 1.0 60 5
Order-No.
33521 115 4 ½ 1.0 60 5
Safety note:
When working with cutting pliers –
beware of wire ends flying away.
Please wear safety glasses.
EN_s230-281_Zangen_2012 15.02.12 17:44 Seite 275