VTech LS6375-3 Quick start - Manual

Quick start guide
LS6375-3 (LS6325-2 and IS6100)
Introduction
This quick start guide provides you with the basic installation
and use instructions. A limited set of features are described in
abbreviated form.
Please refer to the user’s manual for complete installation and
operation instructions
.
Telephone base and charger installation
Install the telephone base and charger as shown below.
®
Telephone base
Telephone
wall jack
Handset charger
Electrical outlet
not controlled by
a wall switch
If you have DSL
high speed
Internet service,
a DSL filter (not
included) is
required.
Telephone
line cord
Telephone base
power adapter
Handset
charger
adapter
Use only the power adapters supplied with this product. •
Handset battery installation and charging
Install the handset battery as shown below. Once you have
installed the handset battery, you may be able to make and receive
short calls. For best performance, charge the handset battery
continuously for at least 16 hours.
Headset charger installation
Install the headset charger as shown below.
Headset charger
Plug the small end of
the headset charger
power adapter into
the power jack of the
headset charger.
Plug the large end of the
headset charger power
adapter into an electrical
outlet not controlled by a
wall switch.
Power on the headset
Power on the headset before use. Place the headset in the headset
charger or press and hold for two seconds. The light flashes
three times in blue and you hear three beeps when the headset is
being powered on.
Headset charging
Charge the headset as shown below. If the light does not turn on
while charging, you need to charge the headset without interruption
for at least 15 minutes to give the headset enough charge to
use for a short time. For best performance, charge the headset
continuously for at least three hours.
Place the tip of
the headset in
the small cradle
on the headset
charger.
1. The magnet holds
the top of the
headset in place.
The light turns on
when charging.
2.
/FIND HANDSET
Page all system
handsets and headset.
Message window
Shows the number
of messages and
other answering
system information.
X/DELETE
Delete the message currently playing.
Press twice to delete all old messages
when the telephone is not in use.
/ANS ON/OFF
Turn the
answering
system on or off.
/PLAY/STOP
Play messages.
Stop message playback.
/VOL and
VOL/
Adjust the
volume during
playback.
Adjust the
telephone base
ringer volume
when the
telephone is not
in use.
IN USE light
Flashes when there
is an incoming call,
or another telephone
sharing the same
line is in use.
On when the
telephone is in use,
or the answering
system is answering
a call.
/SKIP
Skip to the next message.
/REPEAT
Repeat a message or press
twice to play the previous
message.
Telephone base overview
Handset overview
Headset overview
MUTE/FLASH
Mute the microphone
while on a call.
Press and hold to answer
an incoming call when
you receive a call waiting
alert during a call.
Silence the ringer in the
earpiece temporarily
when the headset is
ringing.
+/-/VOLUME
Adjust the
listening volume
while on a call.
Adjust the
ringer volume
when the
headset is not
in use.
Rotating clip
Connect the
ear hook or
head band.
RESET
inset button
Microphone
Earpiece
(on/off)
Press and hold two seconds to power on or off.
Press to answer, end or join a call.
On in red when charging in the headset charger.
On in blue when fully charged in the headset charger.
Flashes once every 10 seconds in blue when in idle mode.
Flashes once every 10 seconds in red when in low battery mode.
Flashes twice every three seconds in blue while on a call.
Flashes quickly and alternately in red and blue while being registered.
Flashes four times every four seconds in blue when there is an
incoming call.
CHARGE light
On when the handset
is charging.
/ VOL
(directory/volume)
Review the directory
when the telephone is not
in use.
Scroll up while in a menu.
Increase the listening
volume during a call.
(speakerphone)
Make, answer or join
a call.
Switch between the
speakerphone and
handset during a call.
/FLASH
Make, answer or join
a call.
Answer another incoming
call during a call.
TONE
Switch to tone dialing
temporarily during a call.
1
Press repeatedly to add
or remove 1 in front of a
call log number before
dialing or saving it in
the directory.
REDIAL/PAUSE
Review the redial list.
Press and hold to insert a
dialing pause while dialing
or entering numbers.
MUTE/REMOVE
Mute the microphone during a call.
Delete the displayed entry while reviewing
the call log, directory or redial list.
Silence the ringer temporarily while the
handset is ringing.
Delete digits when predialing.
VOL/CID
(volume/caller ID)
Review the call log
when the telephone is
not in use.
Scroll down while in
a menu.
Decrease the listening
volume during a call.
MENU/SELECT
Show the menu.
Select an item or save
a setting while in a
menu.
PUSH TO TALK (PTT)
Begin a one-to-one or
one-to-all broadcast
message.
OFF/CLEAR
Hang up a call.
Silence the ringer
temporarily while the
handset is ringing.
Press and hold to
erase the missed call
indicator when the
telephone is not in use.
Return to the previous
menu while in a menu.
Press and hold to
return to idle mode
while in a menu.
Dialing keys
Enter numbers
or characters.
#
Press repeatedly to
show other dialing
options when reviewing
a call log entry.
EQ
Change the audio quality
during an outside call,
intercom call, message or
announcement playback.
Using the menu
To enter the handset menu:
Press MENU/ SELECT when the handset is
not in use.
Press /
VOL or VOL/CID until the
> symbol displays next to the desired
feature menu.
Press
MENU /SELECT to enter that menu.
To return to the previous menu, press
OFF/CLEAR.
To return to idle mode, press and hold
OFF/CLEAR.
Telephone settings
Default settings are indicated by asterisks (*).
1.
2.
3.
•
•
Screen display Function Options
LCD language Set the screen display
language.
English*
Français
Espaňol
Clr voicemail Turn off the voicemail
indicators.
Turn off indicator?
Key tone Set whether the handset beeps
whenever a key is pressed.
On*
Off
Set date/time Set the date and time for the
telephone system.
--:-- --/--
Home area code Set the home area code so
that the call log stores only
seven digits for local telephone
numbers.
_ _ _
Dial mode Set the handset to be tone dial
or pulse dial.
Tone*
Pulse
Telephone operation
Make a call
Press / FLASH or on the handset and
then dial the telephone number. Press on
the headset to join the call and hang up the
handset at any time.
-OR-
Predial by first dialing the telephone number
and then press / FLASH or on the
handset. Press on the headset to join the
call and hang up the handset at any time.
Answer a call
Press on the headset, or /
FLASH , or any of the dialing keys
on the handset.
End a call
Press on the headset or place the headset in its charger.
Press
OFF/ CLEAR on the handset or place the handset in the
telephone base or its charger.
Redial
Each system handset stores the 20 most recently dialed numbers.
When there are already 20 entries, the oldest entry is deleted to
make room for the new entry.
To review and dial a number from the redial list:
Press REDIAL/ PAUSE when the handset
is not in use.
Press /
VOL or VOL/CID or
REDIAL/ PAUSE repeatedly until the
desired entry displays.
Press /
FLASH or to dial.
To delete a redial entry:
When the desired redial entry displays, press
MUTE /REMOVE.
•
•
•
•
1.
2.
3.
Plug the battery connector
securely into the socket,
matching the color-coded label.
1. Place the battery with
the wires inside the
battery compartment.
2.
Slide the battery compartment
towards the center of the
handset until it clicks into place.
3. Charge the handset in the
telephone base.
4.
CHARGE light
remains on
when charging.
>Ringers
Settings
The > symbol
indicates the
feature to select.