Naxa NPB-250 - Manual (Page 5)

9 8
REPEAT AN ALBUM
RANDOM PLAY
INTRODUCTION PLAY
PROGRAMMED PLAY
To repeat a preferred album in playback, press MODE button thrice, "REPT DIR" shows in
the LCD. Then select the preferred album using +10/ALBUM button and SKIP/SERCH
buttons. The player will repeat the chosen album until you press STOP button.
Random play is that tracks on the disc are played by the player at random. Press MODE
button four times to enter this mode during play, "RANDOM" shows in the LCD. Tracks on
the disc will be selected at random for playback and the player stops automatically after all
tracks are played.
Introduction play is that the first ten seconds of each track are played in a sequential order.
Press MODE button five times to enter this mode during play, "INTRO" shows in the LCD.
Press SKIP/SEARCH up button in Introduction mode to begin Introduction play from the
next track immediately after the current track. Press SKIP/SEARCH down button in
Introduction mode to begin Introduction play from the current track. Press MODE button
once more to exit introduction and return to normal playback from the track the unit plays.
Programmed play is that tracks on the disc can be edited for playback in a preferred order
with the use of PROGRAM button.
In MP3 stop mode, press PROGRAM button once, "PROG" shows in the LCD with a
flickering album number and the program sequence indication "P-01"; select the album
number to be programmed using SKIP/SEARCH buttons or +10/ALBUM button, and press
PROGRAM button again to store; the track number flickers waiting for your selection.
Choose the desired track with SKIP/SEARCH buttons or +10/ALBUM button. Press
PROGRAM button again to confirm the first programming and advance to the next
programming step. The program sequence indication changes to "P-02" waiting for your
next input.
Repeat the steps above to program more tracks. A maximum of 99 tracks can be
programmed in memory in a preferred order.
Press PLAY/PAUSE button to begin programmed play in the preferred order after you are
done with programming. The player stops automatically after all programmed tracks are
played.
You may press STOP button to terminate programmed playback. In program stop mode,
press STOP button again to clear the programming; press PLAY/PAUSE button to begin
the programmed playback with the programming order identical with the previous one done.
You may press STOP button to exit random play mode and press
PLAY/PAUSE button to resume normal playback.
Insert a USB data traveller into the USB port insert a MMC/SD card into the card slot;
slide the FUNCTION switch to the USB/CARD position and playback will start from the first
track.
The player reads data from the USB by default if both USB data traveller and MMC/SD
cards are inserted. You may press the USB/CARD button to switch between these modes
in stop mode.
EXTERNAL MEMORY MEDIA OPERATION (USB, MMC/SD)
Prepare the player for external memory media operation
OR
NOTE:
VARIOUS PLAY MODES
SKIPPING TRACKS AND SEARCHING BETWEEN TRACKS
REPEAT MODES
RANDOM PLAY
INTROSCAN PLAY
Press SKIP UP button once to skip the current track and play the next track, press this
button continuously to go to corresponding tracks ahead;
Press SKIP DOWN button once to skip the current track and go back to the previous track,
press this button continuously to go back to corresponding tracks at back.
Press and hold SKIP buttons to initiate high-rate scanning between tracks; release one of
them to begin playback of music at normal speed.
Press MODE button once in play mode to repeat the current track; the LCD shows the icon
for single track repeat.
Press MODE button twice in play mode to repeat tracks on stored on this storage media
(USB/MMC card) as a whole; the LCD shows the icon for all tracks repeat.
Press MODE button thrice to repeat tracks in the current folder as a whole; the LCD shows
the icon for DIR repeat.
Press MODE button for the fourth time in play to activate random playback immediately; the
player will pick up tracks in a random sequence for playback after PLAY/PAUSE button is
pressed. You may press STOP button to exit random play mode and press PLAY/PAUSE
button to resume normal playback.
Press MODE button for the fifth time in play mode to activate introscan playback
immediately; the player will pick up tracks for playback of the first 10 seconds of each track
in a sequential order after PLAY/PAUSE button is pressed. You may press MODE button
once again to exit introscan play mode and return to normal playback from the track it's
arrived at.
AUXILIARY IN
EQ SELECTION
Your player can be used as a power amplifier to playback the programs from portable radio,
TV set or MP3 player or whatever provided this appliance is so designed that audio signal
may be produced through a LINE-OUT jack or the like.
Observe the following steps to connect the player to another appliance:
1. Power the player on using the supplied AC Power Cord.
2. Slide Function Switch to CD/MP3/Aux position.
3. Connect the appliance into the player's AUX in socket with the supplied LINE OUT
cable of the appliance.
4. Power on the appliance and begin play.
Easy job, right? At this time you will be able to hear the sound produced from the programs
the connected appliance is broadcasting.
Press Program/EQ button continuously during disc playback mode to select EQ sound
effects among POP, ROCK, CLASS, JAZZ, BASS and NORMAL.