Bosch GTM 12 JL Professional - Manual (Page 40)

40 | English
1 609 92A 0BP | (9.7.13) Bosch Power Tools
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Technical Data
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardization documents:
EN 61029, EN 60825-1 according to the provisions of the di-
rectives 2011/65/EU, 2004/108/EC, 2006/42/EC,
2009/125/EC (Regulation 1194/2012).
EC Type Examination No. 4811001.12001 by notified test-
ing agency No. 2140.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 09.07.2013
Assembly and Transport
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Carefully remove all parts provided from their packaging.
Remove all packing material from the power tool and the ac-
cessories provided.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Combination saw with pre-mounted saw blade
– Allen key/slotted screwdriver 5
– Dust bag 8
Additionally for table saw:
– Parallel guide 59
– Push stick 60
– Lower saw blade cover 64
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Stationary or Flexible Mounting
 To ensure safe handling, the machine must be mounted
on a level and stable surface (e. g., workbench) prior to
using.
Mounting to a Working Surface (see figures a –b)
– Fasten the power tool with suitable screw fasteners to the
working surface. The mounting holes 3 serve for this pur-
pose.
or
– Clamp the power tool with commercially available screw
clamps by the feet to the working surface.
Mounting to a Bosch Saw Stand
With the height-adjustable legs, Bosch GTA saw stands pro-
vide firm support for the power tool on any surface. The work-
piece supports of the saw stand are used for underlaying long
workpieces.
Combination Saw GTM 12 JL
Article number 3 601 M15 ... ... 0.. ... 061
Rated power input W 1800 1650
No-load speed min -1 3800 3700
Laser type nm
mW
650
< 1
650
< 1
Laser class 2 2
Weight according to
EPTA-Procedure 01/2003
kg 23 23
Protection class /II II /II II
Permissible workpiece dimensions (maximal/minimal):
Chop/mitre saw, see page 44
Table saw, see page 47
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter mm 300 –305
Blade body thickness mm 1.5 –2.0
Mounting hole diameter mm 30
Henk Becker
Executive Vice President
Engineering Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-1688-004.book Page 40 Tuesday, July 9, 2013 11:59 AM